Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL AND OIL FILTER › from 2012.04
RM1840EF _51 Engine / Hybrid System _009602 1GR-FE LUBRICATION _0052409 OIL AND OIL FILTER A

1GR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil drain plug, and drain the engine oil from the oil pan.

NOTICE:

Collect the oil in an oil disposal container.



c.

Wipe the oil pan and drain plug.


d.

Install a new gasket and the drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 2.REMOVE OIL FILTER SUB-ASSEMBLY

a.

When not using drain hose:

i.
A076806
0.5,0.615 0.75,0.615 0.75,0.615 1.365,1.406 true 0.875,0.198 1.125,0.198 1.125,0.198 1.458,0.552 true 0.552,0.094 0.969,0.281 0.417,0.188 10 false SST 0.292,0.531 0.469,0.729 0.177,0.198 10 false *1
*1 Drain Pipe


Remove the drain pipe cap from the drain pipe.


ii.

While removing the oil filter with SST, collect the oil from the oil filter in a container.

SST
09228-07501  


iii.

Install the drain pipe cap.


iv.

Clean the oil catch plate.

HINT:

When using a drain hose, perform the following procedure.



v.

Using SST, remove the oil filter.



b.

When using drain hose:

i.

Remove the drain pipe cap from the drain pipe.


ii.
A076322
1.344,1.729 0.604,1.729 false 0.406,1.635 0.573,1.813 0.167,0.177 10 false *1
*1 Drain Hose


Connect a drain hose to the oil filter bracket.

HINT:
·

Drain hose inside diameter: 8 mm (0.315 in.)

·

Drain hose length: Approximately 900 mm (2.95 ft.)




iii.

Feed the drain hose down through the engine under cover, and put the drain oil container beneath the drain hose to collect the oil from the oil filter.


iv.
A076323
1.104,0.573 1.271,0.573 1.271,0.573 1.5,1.115 false 0.792,0.479 1.115,0.667 0.323,0.188 10 false SST

Using SST, remove the oil filter.

SST
09228-07501  


v.

Remove the drain hose and install the drain pipe cap.


vi.

Clean the oil catch plate.



Hide 3.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.
A076324

Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.


d.
A076325
1.083,0.531 1.229,0.531 1.229,0.531 1.563,1.073 false 0.781,0.438 1.104,0.625 0.323,0.188 10 false SST
V100135

3/4 Turn


Using SST, tighten the oil filter.

SST
09228-07501  

i.

Depending on the work space available, choose from the following.

If enough space is available, use a torque wrench to tighten the oil filter.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.



Hide 4.ADD ENGINE OIL

a.
A308107

Add fresh engine oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil 5W-30
10W-30
(5W-30 is the best choice for good fuel economy and good starting in cold weather)
API grade SL, SM or SN multigrade engine oil 15W-40
20W-50


Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 5.2 liters (5.5 US qts, 4.6 Imp. qts)
Drain and refill with oil filter change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
Dry fill 6.6 liters (7.0 US qts, 5.8 Imp. qts)


NOTICE:

Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

If engine oil is on the location indicated by the arrow, replace the belt tensioner.



b.

Install the oil filler cap.


Hide 6.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.