Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) › from 2012.10
RM1840EF _52 Drivetrain _009610 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0052463 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) C

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE)  P0741  Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)  


DESCRIPTION

The ECM uses the signals from the throttle position sensor, Mass Air Flow (MAF) meter, speed sensor (NC0), speed sensor (SP2) and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical problems of the shift solenoid valve SL, valve body and torque converter.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) Lock-up does not occur when driving in lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in lock-up OFF range (2-trip detection logic)
·

Shift solenoid valve SL remains open or closed

·

Valve body is blocked

·

Shift solenoid valve SL

·

Torque converter

·

Automatic transmission (clutch, brake or gear etc.)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, MAF meter and crankshaft position sensor, the ECM sends a signal to the shift solenoid valve SL to regulate the hydraulic pressure and provide smoother gearshifts. The shift solenoid valve SL responds to commands from the ECM. The valve controls the lock-up relay valve to perform torque converter lock-up and flexible lock-up functions.

The ECM compares the engine speed (NE) signal with the input turbine speed signal to detect torque converter lock-up. The ECM then compares the lock-up status with the lock-up schedule in the ECM memory. If the ECM does not detect lock-up at the appropriate time, it will conclude that there is a malfunction in shift solenoid valve SL. The ECM will illuminate the MIL and store the DTC.

PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0741)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the intelligent tester.

Result:
Result Proceed to
Only P0741 is output A
P0741 and other DTCs are output B


HINT:

If any other codes besides P0741 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SL

B

2.INSPECT SHIFT SOLENOID VALVE SL
a.
C237973
0.094,0.042 0.344,0.26 0.25,0.219 10 false *a 3.063,0.458 3.302,0.677 0.24,0.219 10 false (+) 3.063,1.104 3.302,1.323 0.24,0.219 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL)


Remove shift solenoid valve SL.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SL connector terminal -
Shift solenoid valve SL body
20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SL connector

·

Battery negative (-) → Shift solenoid valve SL body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A343E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A343E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter operates normally.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG