Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2012.04–2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052492 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0717  Turbine Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Turbine Speed Sensor Circuit No Signal All conditions are met for 5 sec. or more (1-trip detection logic):
(a) Gear change: not performed.
(b) Gear position: 4th or 5th.
(c) T/M input shaft speed: 300 rpm or less.
(d) T/M output shaft speed: 1000 rpm or more.
(e) Park/neutral position switch: NSW, R and L input signal are OFF.
(f) Shift solenoid valves and park/neutral position switch: in normal operation.
·

Open or short in speed sensor NT circuit

·

Speed sensor NT

·

ECM

·

Automatic transmission (clutch, brake, gear, etc.)


Comes on DTC stored

Reference: Inspect using an oscilloscope.

Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
C130-35 (NT+) - C130-27 (NT-) 1 V/DIV., 2 msec./DIV. Engine idling (shift lever in P or N) Refer to illustration


C162170
2.708,0.177 3.292,0.375 0.583,0.198 10 false 1 V/DIV. 2.99,0.958 3.344,1.156 0.354,0.198 10 false GND 1.667,1.76 2.479,1.958 0.813,0.198 10 false 2 msec./DIV.

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal by comparing the input speed sensor NT signal with the output speed sensor SP2 signal.

While the vehicle is operating in 4th or 5th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
·

*1: A pulse is not output or is irregularly output.

·

*2: The vehicle speed is approximately 50 km/h (30 mph) or more.



WIRING DIAGRAM

C258073
1.281,1.25 1.531,1.438 0.25,0.188 10 false 1 1.281,2.094 1.531,2.281 0.25,0.188 10 false 2 0.823,2.365 1.25,2.552 0.427,0.188 10 false C149 5.615,1.125 5.979,1.313 0.365,0.188 10 false NT+ 5.344,1.26 5.563,1.448 0.219,0.188 10 false 35 5.615,2.24 5.979,2.427 0.365,0.188 10 false NT- 5.781,3.031 6.24,3.219 0.458,0.188 10 false C130 5.781,3.219 6.24,3.406 0.458,0.188 10 false ECM 5.344,2.385 5.563,2.573 0.219,0.188 10 false 27 0.823,2.563 2.073,2.75 1.25,0.188 10 false Speed Sensor NT

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the tester, read the Data List.

Powertrain > Engine > Data List
Tester Display
SPD (NT)
50003 61 141
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

·

Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm.
HINT:
·

SPD (NT) is always 0 while driving:

Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:

Sensor trouble, improper installation or intermittent connection trouble in the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR NT INSTALLATION
a.
C211922
0.865,0.219 1.104,0.417 0.24,0.198 10 false *a 2.323,0.229 2.563,0.427 0.24,0.198 10 false *b
*a CORRECT
*b INCORRECT


Check the speed sensor NT installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



Result:
Proceed to
OK
NG



OK

2.INSPECT SPEED SENSOR NT

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR NT

2.INSPECT SPEED SENSOR NT
a.
C206284
1.302,1.688 1.604,1.146 true 2.146,1.688 1.792,1.146 true 0.073,0.083 0.313,0.281 0.24,0.198 10 false *a 1.219,1.708 1.667,1.906 0.448,0.198 10 false 2 2.156,1.698 2.604,1.896 0.448,0.198 10 false 1
*a Component without harness connected
(Speed Sensor NT)


Disconnect the speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)
a.
C237600
0.896,0.333 1.302,0.573 0.406,0.24 0.51,2.74 0.844,2.104 true 0.854,2.177 1.208,2.76 true 1.042,2.792 2.448,2.948 1.406,0.156 10 false 35 (NT+) 0.938,0.365 1.302,0.563 0.365,0.198 10 false C130 0.313,2.792 1.719,2.948 1.406,0.156 10 false 27 (NT-) 0.094,0.052 0.375,0.385 0.281,0.333 10 false *a
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C130-35 (NT+) - C130-27 (NT-) 20°C (68°F) 560 to 680 Ω
C130-35 (NT+) - Body ground Always 10 kΩ or higher
C130-27 (NT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR