Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2012.04–2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052492 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the solenoid is controlled by the ECM. During the lock-up operation, if the current increases, the lock-up hydraulic pressure increases.

C221407
4.729,2.135 5.031,1.188 5.031,1.188 5.094,1.188 true 4.969,2.323 5.125,2.688 5.125,2.688 5.188,2.688 true 5.76,2.396 5.917,2.688 5.917,2.688 5.979,2.688 true 6.031,2.594 6.917,2.813 0.885,0.219 10 false Solenoid Coil 0.135,0.688 1.385,0.906 1.25,0.219 10 false Hydraulic Pressure 2.573,3.01 3.135,3.229 0.563,0.219 10 false Current 5.24,2.615 5.771,2.833 0.531,0.219 10 false Sleeve 5.167,1.104 6.01,1.323 0.844,0.219 10 false Spool Valve

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) Open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve (SLU) circuit is detected, the ECM determines there is a malfunction. The ECM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C220887
2.813,1.344 3.156,1.563 0.344,0.219 10 false 13 5.417,1.344 5.74,1.573 0.323,0.229 10 false 15 2.26,1.115 2.979,1.344 0.719,0.229 10 false SLU+ 2.813,2.563 3.25,2.865 0.438,0.302 10 false 5 2.302,2.302 2.844,2.583 0.542,0.281 10 false SLU- 5.76,1.229 6.302,1.469 0.542,0.24 10 false SLU+ 5.417,2.563 5.781,2.813 0.365,0.25 10 false 14 5.781,2.448 6.302,2.688 0.521,0.24 10 false SLU- 0.969,2.896 1.563,3.115 0.594,0.219 10 false C151 0.969,3.073 2.542,3.438 1.573,0.365 10 false Transmission Wire 1.021,1.813 2.938,2.115 1.917,0.302 10 false Shift Solenoid Valve SLU 5.948,3.219 6.427,3.438 0.479,0.219 10 false C130 5.958,3.375 6.375,3.625 0.417,0.25 10 false ECM 0.823,1.385 1.135,1.615 0.313,0.229 10 false 2 0.844,2.208 1.094,2.427 0.25,0.219 10 false 1

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C214326
1.573,1.302 1.385,1.729 true 1.646,1.104 1.906,1.75 true 1.177,1.781 1.583,1.948 0.406,0.167 10 false SLU+ 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a 1.771,1.781 2.146,1.948 0.375,0.167 10 false SLU-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLU+) - 5 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLU+) - Body ground Always 10 kΩ or higher
5 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C237600
0.896,0.333 1.302,0.573 0.406,0.24 1.094,2.042 1.531,2.813 true 1.031,2.052 0.552,2.813 true 1.292,2.885 2.031,3.104 0.74,0.219 10 false 14 (SLU-) 0.938,0.365 1.302,0.563 0.365,0.198 10 false C130 0.094,0.052 0.375,0.385 0.281,0.333 10 false *a 0.219,2.885 1.01,3.177 0.792,0.292 10 false 15 (SLU+)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C130-15 (SLU+) - C130-14 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C130-15 (SLU+) - Body ground Always 10 kΩ or higher
C130-14 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.
C209928
1.771,0.969 2.219,0.385 true 1.469,0.969 1.01,0.385 true 1.76,2.948 2.208,2.354 true 1.458,2.948 1,2.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.26,0.271 2.427,0.469 0.167,0.198 10 false 1 0.896,0.26 1.063,0.458 0.167,0.198 10 false 2 2.24,2.24 2.406,2.438 0.167,0.198 10 false 1 0.885,2.25 1.052,2.448 0.167,0.198 10 false 2 1.927,3.958 2.125,4.156 0.198,0.198 10 false (-) 1.115,3.969 1.333,4.167 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLU)


Remove shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes operating noise



Result:
Proceed to
OK
NG



OK

NG