Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2012.04–2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052492 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0818  Driveline Disconnect Switch Input Circuit  


DESCRIPTION

The ECM detects the signal from the No. 2 transfer indicator switch (transfer neutral position switch).

This DTC indicates that the signal indicating that the transfer neutral position switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0818 Driveline Disconnect Switch Input Circuit The signal indicating that the transfer neutral position switch remains on while the vehicle is running under the following conditions for 30 seconds (2-trip detection logic):
·

The vehicle speed is 25 km/h (15.54 mph) or more.

·

The transfer position switch is in H.


·

Short in No. 2 transfer indicator switch circuit

·

No. 2 transfer indicator switch (transfer neutral position switch)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM detects whether or not the transfer is in neutral by monitoring the signal from the transfer neutral position switch.

If the ECM detects that the transfer is in neutral under the following conditions, the ECM will conclude that there is a malfunction of the transfer neutral position switch, illuminate the MIL and store the DTC:

·

The transfer neutral position switch indicates that the transfer shift lever is in neutral.

·

The transfer shift lever is in the "H" position.

·

The vehicle is being driven at 25 km/h (15.54 mph) or more.

·

The transfer neutral signal has been on for more than 30 seconds.


WIRING DIAGRAM

C154998
6.104,2.969 6.625,3.177 0.521,0.208 10 false ECM 5.906,1.313 6.427,1.521 0.521,0.208 10 false TFN 5.635,1.406 5.938,1.615 0.302,0.208 10 false 25 3.646,1.396 3.802,1.604 0.156,0.208 10 false 1 2.885,1.406 3.073,1.615 0.188,0.208 10 false 2 6.094,2.792 6.615,3 0.521,0.208 10 false C130 2.323,1.615 2.625,1.823 0.302,0.208 10 false C30 2.323,1.813 4.552,2.208 2.229,0.396 10 false No. 2 Transfer Indicator Switch (Transfer Neutral Position Switch)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237628
0.49,1.104 0.906,1.396 0.417,0.292 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 0.573,1.167 0.938,1.365 0.365,0.198 10 false C30
*a Front view of wire harness connector
(to No. 2 Transfer Indicator Switch)


Disconnect the No. 2 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)
a.
C237864
0.052,0 0.229,0.198 0.177,0.198 10 false *a 0.25,2.813 0.427,3.01 0.177,0.198 10 false *c 0.969,2.813 1.146,3.01 0.177,0.198 10 false *b
*a Component without harness connected
(No. 2 Transfer Indicator Switch)
*b Pushed
*c Not pushed


Remove the No. 2 transfer indicator switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pushed Below 1 Ω
1 - 2 Not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - ECM)

NG

REPLACE NO. 2 TRANSFER INDICATOR SWITCH

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - ECM)
a.

Disconnect the C30 No. 2 transfer indicator switch connector.


b.

Disconnect the C130 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-1 - C130-25 (TFN) Always Below 1 Ω
C30-1 or C130-25 (TFN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR