Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY(for 1KD-FTV) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052503 AUTOMATIC TRANSMISSION ASSEMBLY(for 1KD-FTV) A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1KD-FTV)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 6.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C239519

Remove the 4 screws and shift lever boot.


Hide 7.REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

a.

Fold back the transfer front drive shift boot.


b.
C213734

Using needle-nose pliers, remove the snap ring and pull out the shift lever.

HINT:

Move the transfer shift lever to the H4 position.



Hide 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 13.DISCONNECT OIL COOLER TUBE

C187501

a.

Using a union nut wrench, disconnect the tube outlet and tube inlet.


b.
C187500

Remove the 3 bolts and 3 clamps.


Hide 14.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C111231

a.

Remove the nut and clip and disconnect the control cable.


Hide 15.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C111232

a.

Remove the 2 bolts and control cable bracket from the transmission.


Hide 16.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C111233

a.

Support the transmission with a transmission jack.


Hide 17.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034256

a.

Remove the 4 set bolts of the rear No. 1 engine mounting insulator.


b.

Remove the 4 nuts, 4 bolts and frame crossmember.


Hide 18.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

G034260

a.

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.


Hide 19.DISCONNECT WIRE HARNESS

a.
C214940

Remove the nut and disconnect the ground cable.


b.
C112845

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



c.

Disconnect the 8 connectors and detach the 7 clamps.


d.

Remove the bolt and disconnect the wire harness.


Hide 21.REMOVE STIFFENER PLATE

C187502C01
0.135,0.135 0.396,0.354 0.26,0.219 10 true *A 0.135,2.438 0.427,2.688 0.292,0.25 10 true *B
*A LH Side
*B RH Side


a.

Remove the 4 bolts and stiffener plate RH (with oil cooler tube clamp).


b.

Remove the 4 bolts and stiffener plate LH.


c.

Remove the No. 4 cylinder block insulator.


d.

Remove the end plate.


Hide 22.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
G034258

Turn the crankshaft to gain access to the 6 torque converter setting bolts and remove each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.


Hide 23.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C283593

Remove the 5 bolts.


b.

Remove the automatic transmission assembly.

NOTICE:
·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.

·

Do not use excess force to pry on the transmission assembly.




Hide 25.REMOVE TORQUE CONVERTER ASSEMBLY