Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE › from 2012.04
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052505 TORQUE CONVERTER AND DRIVE PLATE G

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

AT05437
1.188,1.115 1.365,1.792 true 1.281,1.823 1.646,2.01 0.365,0.188 10 false SST
V100135

Free
V100136

Lock


a.

Inspect the 1-way clutch.

i.

Install SST to the inner race of the 1-way clutch.

SST
09350-32014  (09351-32020)


ii.

Press on the serrations of the starter with a finger and rotate it.

Check if it rotates smoothly when turned clockwise and locks when turned counterclockwise.

If the results are not as specified, clean the converter and recheck the 1-way clutch. If the results still are not as specified, replace the torque converter clutch assembly.



b.
C197457
0.113,0.051 0.341,0.247 0.228,0.196 10 *1
*1 Sample showing maximum allowable amount of powder in ATF


Determine the condition of the torque converter clutch.

i.

Check that the following conditions are met:

·

During the stall test or when the shift lever is in N, metallic sounds are not emitted from the torque converter clutch.

·

The 1-way clutch turns in one direction and locks in the other direction.

·

The amount of powder in the ATF is not more than the sample shown in the illustration.


If the results are not as specified, replace the torque converter clutch assembly.

HINT:

The sample illustration shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF taken from a removed torque converter clutch.




c.

Replace the ATF in the torque converter clutch.

i.

AT If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter clutch thoroughly and drain the ATF with the torque converter facing upward.



d.
D025368
1.75,1.865 2.177,1.719 true 0.5,0.25 0.688,0.448 0.188,0.198 10 false *a 1.531,0.26 1.729,0.458 0.198,0.198 10 false *b 2.229,1.583 2.427,1.781 0.198,0.198 10 false *c
*a Correct
*b Incorrect
*c Bottom is damaged


Prevent deformation of the torque converter clutch and damage to the oil pump gear.

i.

When any marks due to interference are found on the end of the bolt for the torque converter clutch and on the bottom of the bolt hole, replace the bolt and torque converter clutch.


ii.

All of the bolts should be the same length.


iii.

Make sure no spring washers are missing.



Hide 2.INSPECT DRIVE PLATE

a.

Check the drive plate for damage.


b.
C284235
0.104,0.104 0.417,0.26 0.313,0.156 10 false *A 0.125,2.188 0.438,2.344 0.313,0.156 10 false *B 0.448,4.271 0.76,4.427 0.313,0.156 10 false *1 1.385,3.177 1.542,3.375 0.156,0.198 10 false 1 1.906,4.063 2.063,4.26 0.156,0.198 10 false 6 2.729,4.146 2.885,4.344 0.156,0.198 10 false 5 3.031,3.396 3.188,3.594 0.156,0.198 10 false 4 2.552,2.573 2.708,2.771 0.156,0.198 10 false 3 1.833,2.458 1.99,2.656 0.156,0.198 10 false 2 1.885,2.094 2.042,2.292 0.156,0.198 10 false 6 1.302,1.219 1.458,1.417 0.156,0.198 10 false 1 1.729,0.49 1.885,0.688 0.156,0.198 10 false 2 2.51,0.667 2.667,0.865 0.156,0.198 10 false 3 2.938,1.344 3.094,1.542 0.156,0.198 10 false 4 2.688,2.104 2.844,2.302 0.156,0.198 10 false 5
*A for 1GR-FE
*B for 1KD-FTV
*1 Measuring Point


Set up a dial indicator and measure the runout of the 6 portions around the torque converter clutch contact surfaces.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is more than the maximum, or the drive plate is damaged, replace the drive plate (See page for 1GR-FE: Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>INSTALLATION, for 1KD-FTV: Engine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY(w/ Glow Plug Controller)>INSTALLATION).