Home › Drivetrain › R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › 2012.10–2013.10
RM1840EF _52 Drivetrain _009614 R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE _0052523 MANUAL TRANSMISSION UNIT A

R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE FILLER PLUG

a.
D029023

Remove the filler plug and gasket from the transmission case.


Hide 2.REMOVE DRAIN PLUG

a.
D029024

Remove the drain plug and gasket from the transmission case.


Hide 3.REMOVE CLUTCH RELEASE FORK BOOT

Hide 4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 5.REMOVE RELEASE FORK SUPPORT

Hide 6.REMOVE CLUTCH HOUSING

a.
C238801
0.115,0.0 0.346,0.231 0.231,0.231 10 *A 0.115,2.139 0.346,2.37 0.231,0.231 10 *B
*A for TR Engine series
*B for 1KD-FTV, 2KD-FTV


Remove the 9 bolts.


b.
D029029

Using a plastic-faced hammer, tap off the clutch housing from the transmission case.


Hide 7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
D029030
2.531,1.875 1.854,1.031 true 2.448,1.927 2.792,2.135 0.344,0.208 10 false SST

Using SST, remove the back-up light switch and gasket from the transmission case.

SST
09817-16011  


Hide 8.REMOVE SPEEDOMETER SENSOR

a.

Remove the bolt and speedometer sensor.


b.

Remove the O-ring from the speedometer sensor.


Hide 9.REMOVE RESTRICT PIN

a.
C116362

Remove the 2 restrict pins from the extension housing.


Hide 10.REMOVE CONTROL SHIFT LEVER RETAINER

a.
C116363

Remove the 6 bolts.


b.

Remove the control shift lever retainer.


c.

Remove the control shift lever retainer gasket.


Hide 11.REMOVE EXTENSION HOUSING

a.
G034547

Remove the bolt from the shift lever housing.


b.
C282329

Remove the 10 bolts.


c.
G034242

Using a plastic-faced hammer, tap the extension housing and remove the shift lever housing and the shift and select lever from the transmission case.


Hide 12.REMOVE OIL RECEIVER PIPE

D029037

Hide 13.REMOVE OIL RECEIVER

a.

Remove the bolt and oil receiver.


Hide 14.REMOVE REVERSE RESTRICT PIN

a.
D029040

Using a T40 ''TORX'' socket wrench, remove the plug.


b.
C283133

Using a 5 mm pin punch and a hammer, tap out the restrict slotted pin.


c.
D029042

Remove the restrict pin.


Hide 15.REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

a.

Using a screwdriver and hammer, tap out the manual transmission extension housing oil seal from the extension housing.


Hide 16.REMOVE FRONT BEARING RETAINER

a.
D025950

Remove the 8 bolts.


b.
D025951

Using a brass bar and hammer, tap off the retainer from the transmission case.


Hide 17.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

a.
D025952
1.875,0.792 2.313,0.354 false 2.385,0.208 2.74,0.417 0.354,0.208 10 false SST

Secure the front bearing retainer in a vise.


b.

Using SST, tap out the oil seal.

SST
09308-00010  


Hide 18.REMOVE FRONT BEARING SHAFT SNAP RING

a.
D025953

Using a snap ring expander, remove the snap ring from the transmission case.


Hide 19.REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

a.
D025954

Using a snap ring expander, remove the snap ring from the transmission case.


Hide 20.REMOVE MANUAL TRANSMISSION CASE

a.
D029044

Using a brass bar and hammer, tap off the transmission case from the intermediate plate.


Hide 21.REMOVE TRANSMISSION MAGNET

a.
D025957

Remove the magnet from the intermediate plate.


Hide 22.SECURE INTERMEDIATE PLATE

a.
D029045

Secure the intermediate plate in a vise between aluminum plates.


Hide 23.REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT

a.
D029046

Using a T40 ''TORX'' socket wrench, remove the spring seat from the intermediate plate.


b.
D025960

Using a magnet hand, remove the compression spring and detent ball from the intermediate plate.


c.
D033569

Using a T40 ''TORX'' socket wrench, remove the 2 spring seats from the intermediate plate.


d.
D033570

Using a magnet hand, remove the 2 compression springs and 2 detent balls from the intermediate plate.


Hide 24.REMOVE NO. 2 SHIFT FORK SHAFT

a.
D029048

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 2 shift fork shaft.

NOTICE:

Use a cloth to prevent the snap ring from flying off.



b.
D029049

Remove the bolt from the No. 2 shift fork.


c.
D029050

Remove the No. 2 shift fork shaft from the intermediate plate.


d.
D029051

Remove the No. 2 shift fork from the No. 2 transmission hub sleeve.


e.
D025967

Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.


Hide 25.REMOVE NO. 1 SHIFT FORK SHAFT

a.
D029052

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 1 shift fork shaft.

NOTICE:

Use a cloth to prevent the snap ring from flying off.



b.
D029053

Remove the shift fork set bolt from the No. 1 shift fork.


c.
D029054

Remove the No. 1 shift fork shaft from the intermediate plate.


d.
D029055

Remove the No. 1 shift fork from the reverse gear.


e.
D025975

Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.


Hide 26.REMOVE NO. 3 SHIFT FORK SHAFT

a.
C272920

Using a 5 mm pin punch and hammer, tap out the shift fork set slotted pin from the No. 3 shift fork.


b.
D029057

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 3 shift fork shaft.

NOTICE:

Use a cloth to prevent the snap ring from flying off.



c.
C272922

Remove the No. 3 shift fork and No. 3 shift fork shaft from the intermediate plate.


d.
D025975

Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.


e.
D025979

Using a magnet hand, remove the reverse shift fork ball from the reverse shift fork.


Hide 27.REMOVE NO. 4 SHIFT FORK SHAFT

a.
D025980

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 4 shift fork shaft.

NOTICE:

Use a cloth to prevent the snap ring from flying off.



b.
C089440

Remove the No. 4 shift fork shaft from the intermediate plate.

NOTICE:

Cover the hole with a cloth to prevent the reverse shift fork ball from popping out.



c.
D025982

Using a magnet hand, remove the reverse shift fork return compression spring from the reverse shift fork.


Hide 28.REMOVE REVERSE SHIFT FORK

a.
D025983

Remove the reverse shift fork together with the reverse shift arm from the intermediate plate.


b.
D025984

Using a screwdriver, pry out the E-ring and reverse shift fork from the reverse shift arm.


Hide 29.REMOVE REVERSE SHIFT ARM BRACKET

a.
D025985

Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.


Hide 30.REMOVE SPEEDOMETER DRIVE GEAR

a.
G034243

Using snap ring pliers, remove the snap ring.


b.

Remove the drive gear.


c.

Using a magnet hand, remove the steel ball.


d.

Using snap ring pliers, remove the snap ring.


Hide 31.REMOVE OUTPUT SHAFT REAR BEARING

a.
C238817

Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the output shaft.


b.
C112600

Using SST, remove the rear bearing and output shaft spacer from the output shaft.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


Hide 34.REMOVE COUNTER GEAR REAR SHAFT SNAP RING

a.
C272924

Using 2 screwdrivers and a hammer, tap off the snap ring from the counter gear.


Hide 35.REMOVE NO. 3 TRANSMISSION HUB SLEEVE

a.
C272925

Remove the No. 3 transmission hub sleeve from the counter 5th gear.


Hide 36.REMOVE COUNTER 5TH GEAR

a.
C272926
1.323,1.885 1.49,1.885 1.49,1.885 1.427,1.5 false 1.021,1.802 1.333,1.958 0.313,0.156 10 true SST

Using SST, remove the counter 5th gear together with the 2 No. 3 synchromesh shifting keys, 2 No. 3 synchromesh shifting key springs, No. 3 synchronizer ring and No. 5 gear spline piece from the counter gear.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04021, 09957-04010, 09958-04011)


Hide 37.REMOVE NO. 5 GEAR SPLINE PIECE

a.
C238819

Remove the No. 5 gear spline piece from the counter 5th gear.


Hide 38.REMOVE NO. 3 SYNCHRONIZER RING

a.

Remove the synchronizer ring from the counter 5th gear.


Hide 39.REMOVE COUNTER 5TH GEAR BEARING

a.
C089839

Remove the bearing from the counter 5th gear.


Hide 40.REMOVE NO. 3 TRANSMISSION HUB SLEEVE

C247403

a.

Using a snap ring expander, remove the snap ring.


b.
C250077

Remove the No. 3 synchromesh shifting key spring and 2 No. 3 synchromesh shifting keys from the counter 5th gear.


Hide 41.REMOVE 5TH GEAR THRUST WASHER

a.
C272928

Remove the thrust washer from the counter gear.


Hide 42.REMOVE 5TH GEAR THRUST WASHER PIN

a.
C272930

Remove the thrust washer pin from the counter gear.


Hide 43.REMOVE REAR BEARING RETAINER

a.
D026001

Remove the 4 bolts and bearing retainer from the intermediate plate.


Hide 44.REMOVE REVERSE IDLER GEAR

a.
D026002

Pull out the reverse idler gear shaft from the rear side and remove the reverse idler gear from the intermediate plate.


Hide 45.REMOVE COUNTER SHAFT CENTER BEARING

a.
D029260

Using a snap ring expander, remove the snap ring.


b.
C272934
1.469,2 1.656,2 1.656,2 1.813,1.844 true 1.177,1.906 1.479,2.063 0.302,0.156 10 true SST

Using SST, remove the center bearing from the intermediate plate.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

HINT:

Remove the bearing while tapping the tip of the counter gear so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.



Hide 46.REMOVE COUNTER GEAR ASSEMBLY

a.
D026005

Remove the counter gear from the intermediate plate.


Hide 47.REMOVE INPUT SHAFT ASSEMBLY

a.
D026006

Remove the input shaft and No. 2 synchronizer ring from the output shaft.

NOTICE:

Do not drop the input shaft bearing or No. 2 synchronizer ring.



Hide 48.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C272936

Using a snap ring expander, remove the snap ring from the output shaft.


Hide 49.REMOVE OUTPUT SHAFT ASSEMBLY

a.
C272937

Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.