Home › Drivetrain › R150F /R151F / R156F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › 2011.10–2012.10
RM1840EF _52 Drivetrain _009615 R150F /R151F / R156F MANUAL TRANSMISSION / TRANSAXLE _0052533 MANUAL TRANSMISSION UNIT A

R150F /R151F / R156F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL OUTPUT SHAFT ASSEMBLY

a.
C272540

Apply gear oil to the sliding part of the output shaft.


b.

Using a plastic-faced hammer, install the output shaft by tapping the intermediate plate.


Hide 2.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
D029064

Using a snap ring expander, install the shaft snap ring to the output shaft.


Hide 3.INSTALL INPUT SHAFT ASSEMBLY

a.
D026006

Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

NOTICE:
·

Install the No. 2 synchronizer ring so the No. 2 synchromesh shifting key fits into the groove of the No. 2 synchronizer ring.

·

Check that the input shaft rotates slightly.




Hide 4.INSTALL COUNTER GEAR

a.
D026005

Temporarily install the counter gear to the intermediate plate.


Hide 5.INSTALL COUNTER SHAFT CENTER BEARING

a.
D029113
2.656,0.781 2.427,1.198 false 2.708,0.646 3.073,0.875 0.365,0.229 10 false SST

Using SST and a hammer, tap in a new center bearing to the intermediate plate.

SST
09316-60011  (09316-00011)

HINT:

Install the bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.



Hide 6.INSTALL REVERSE IDLER GEAR

a.
D026002

Apply gear oil to each sliding part of the reverse idler gear and the reverse idler gear shaft, and install reverse idler gear and the reverse idler shaft to the intermediate plate.

NOTICE:

Install the reverse idler shaft with its groove facing the rear side, and install it from the rear side.



Hide 7.INSTALL REAR BEARING RETAINER

a.
D026001

Insert the bearing retainer into the groove of the reverse idler gear shaft and install it with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 8.INSTALL 5TH GEAR THRUST WASHER PIN

a.
D026000

Apply MP grease to the washer pin, and install it to the counter gear.


Hide 9.INSTALL 5TH GEAR THRUST WASHER

a.
D025999

Apply gear oil to the thrust washer, and install it to the counter gear.

NOTICE:

Install the thrust washer so that its chamfer side faces forward.



Hide 10.INSTALL NO. 3 TRANSMISSION HUB SLEEVE

a.

Apply gear oil to the sliding part of the No. 3 transmission hub sleeve, and install it to the counter 5th gear.

NOTICE:

Be sure of the direction of the No. 3 transmission hub sleeve and counter 5th gear.



b.

Install the No. 3 synchromesh shifting key spring.

i.
C250774

for Type A:

Install the 2 No. 3 synchromesh shifting keys and 2 synchromesh shifting key springs to the counter 5th gear.


ii.
C248514
1.24,3.042 1.448,3.042 1.448,3.042 1.313,2.708 true 1.781,3.052 1.688,3.052 1.688,3.052 1.552,2.667 true 1.01,2.938 1.167,3.094 0.156,0.156 10 true *a 1.823,2.958 1.979,3.115 0.156,0.156 10 true *b
*a Cutout
*b Protrusion


for Type B:

Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.

HINT:

When installing the synchromesh shifting key spring, make sure the protrusion fits into the cutout.




c.
C247403

Using a snap ring expander, install the snap ring to the counter 5th gear.


Hide 11.INSTALL COUNTER 5TH GEAR BEARING

a.
D026020

Apply gear oil to the bearing and install it to the counter 5th gear.


Hide 12.INSTALL COUNTER 5TH GEAR

a.
D025996

Apply gear oil to the 5th gear and No. 3 transmission hub sleeve, and install them to the counter gear.


Hide 13.INSTALL NO. 3 SYNCHRONIZER RING

a.
D029060

Apply gear oil to the No. 3 synchronizer ring, and install it to the counter gear.

NOTICE:

Install the No. 3 synchronizer ring so that the No. 3 synchromesh shifting key fits into the groove of the No. 3 synchronizer ring.



Hide 14.INSTALL NO. 5 GEAR SPLINE PIECE

a.
D026022
2.365,0.521 1.823,0.521 false 2.448,0.438 2.813,0.635 0.365,0.198 10 false SST

Using SST and a press, press in the gear spline piece to the counter gear.

SST
09316-60011  (09316-00011)

NOTICE:

Check that the gear rotates freely.



Hide 15.INSTALL COUNTER GEAR REAR SHAFT SNAP RING

a.

Select a snap ring so that the thrust clearance between the No. 5 gear spline piece and snap ring is within the specification.

Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Mark Thickness
A 2.80 to 2.85 mm (0.1102 to 0.1122 in.)
B 2.85 to 2.90 mm (0.1122 to 0.1141 in.)
C 2.90 to 2.95 mm (0.1141 to 0.1160 in.)
D 2.95 to 3.00 mm (0.1160 to 0.1181 in.)
E 3.00 to 3.05 mm (0.1181 to 0.1200 in.)
F 3.05 to 3.10 mm (0.1200 to 0.1220 in.)
G 3.10 to 3.15 mm (0.1220 to 0.1240 in.)



b.
D026023

Using a brass bar and hammer, tap on the snap ring.


Hide 18.INSTALL OUTPUT SHAFT REAR BEARING

a.
D026024
2.396,0.583 2.156,1.01 false 2.323,0.406 2.656,0.615 0.333,0.208 10 false SST

Using SST and a press, press in the spacer and a new rear bearing to the output shaft.

SST
09309-35010  


Hide 19.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.

Select a shaft snap ring so that the thrust clearance between the output shaft bearing shaft and snap ring is within the specification.

Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Mark Thickness Mark Thickness
A 2.65 to 2.70 mm (0.1043 to 0.1063 in.) K 3.10 to 3.15 mm (0.1220 to 0.1240 in.)
B 2.70 to 2.75 mm (0.1063 to 0.1083 in.) L 3.15 to 3.20 mm (0.1240 to 0.1260 in.)
C 2.75 to 2.80 mm (0.1083 to 0.1102 in.) M 3.20 to 3.25 mm (0.1260 to 0.1280 in.)
D 2.80 to 2.85 mm (0.1102 to 0.1122 in.) N 3.25 to 3.30 mm (0.1280 to 0.1299 in.)
E 2.85 to 2.90 mm (0.1122 to 0.1141 in.) P 3.30 to 3.35 mm (0.1299 to 0.1319 in.)
F 2.90 to 2.95 mm (0.1141 to 0.1160 in.) Q 3.35 to 3.40 mm (0.1319 to 0.1339 in.)
G 2.95 to 3.00 mm (0.1160 to 0.1181 in.) R 3.40 to 3.45 mm (0.1339 to 0.1358 in.)
H 3.00 to 3.05 mm (0.1181 to 0.1200 in.) S 3.45 to 3.50 mm (0.1358 to 0.1378 in.)
J 3.05 to 3.10 mm (0.1200 to 0.1220 in.) - -



b.
D025988

Using a brass bar and hammer, tap on the snap ring.


Hide 20.INSTALL REVERSE SHIFT ARM BRACKET

a.
D025985

Install the arm bracket to the intermediate plate with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 21.INSTALL REVERSE SHIFT FORK

a.
D026025

Install the shift arm to the shift fork. Using a screwdriver and hammer, tap on a new E-ring.


b.
D026026

Install the tip of the reverse shift arm to the reverse idler gear. Align the end of the reverse shift arm that has the cutout with the reverse shift arm bracket pin, and install the reverse shift arm and reverse shift fork.


Hide 22.INSTALL NO. 4 SHIFT FORK SHAFT

a.
D026027

Install the compression spring and reverse shift fork ball to the reverse shift fork.


b.
D025981

Apply gear oil to the sliding part of the No. 4 shift fork shaft.


c.

Using a screwdriver, install the No. 3 shift fork shaft by pushing the reverse shift fork ball lightly.


d.
D026028

Using a brass bar and a hammer, tap on the snap ring to the No. 4 shift fork shaft.


Hide 23.INSTALL NO. 3 SHIFT FORK SHAFT

a.
D025979

Install the reverse shift fork ball to the reverse shift fork.


b.
D025975

Install the No. 1 shift interlock roller to the intermediate plate.


c.
D029058

Install the No. 3 shift fork to the No. 3 transmission hub sleeve and No. 3 shift fork shaft to the intermediate plate from the front side.


d.
D029114

Using a brass bar and hammer, tap on the snap ring to the shift fork shaft.


e.
D029056

Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the No. 3 shift fork.


Hide 24.INSTALL NO. 1 SHIFT FORK SHAFT

a.
D025975

Install the No. 1 shift interlock roller to the intermediate plate.


b.
D029055

Install the No. 1 shift fork to the reverse gear.


c.
D029054

Install the No. 1 shift fork shaft to the intermediate plate from the rear side.


d.
D029053

Install a new shift fork set bolt to the No. 1 shift fork.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


e.
D029115

Using a brass bar and hammer, tap on the shift fork shaft snap ring to the No. 1 shift fork shaft.


Hide 25.INSTALL NO. 2 SHIFT SHAFT

a.
D025967

Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.


b.
D029051

Install the No. 2 shift fork to the No. 2 transmission hub sleeve.


c.
D029050

Apply gear oil to the No. 2 shift fork, and install the shift fork to the intermediate plate from the rear side.


d.
D029049

Install a new shift fork set bolt to the No. 2 shift fork.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


e.
D029116

Using a brass bar and hammer, tap on the snap ring to the No. 2 shift fork shaft.


Hide 26.INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT

a.
D033570

Install the 2 compression springs and 2 shifts detent balls to the intermediate plate.


b.
D033569

Using a T40 ''TORX'' socket wrench, install the 3 spring seats to the intermediate plate.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


c.
D025960

Install the detent ball and low side compression spring to the intermediate plate.


d.
D029046

Using a T40 ''TORX'' socket wrench, install the spring seat to the intermediate plate.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 27.INSTALL TRANSMISSION MAGNET

a.
D025957

Clean the transmission magnet, and install it to the intermediate plate.


Hide 28.INSTALL MANUAL TRANSMISSION CASE

a.
D029067
2.583,0.5 2.938,0.365 true 2.979,0.271 3.167,0.448 0.188,0.177 10 false *1
*1 Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



b.
D029117

Using a plastic-faced hammer, tap the transmission case to attach it to the intermediate plate.


Hide 29.INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

a.
D025954

Using a snap ring expander, install the snap ring to the transmission case.


Hide 30.INSTALL FRONT BEARING SHAFT SNAP RING

a.
D025953

Using a snap rig expander, install the snap ring to the transmission case.


Hide 31.INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

a.
D026035
2.375,1.104 2.615,0.323 true 2.479,0.094 2.844,0.292 0.365,0.198 10 false SST

Using SST and a hammer, tap in a new oil seal to the front bearing retainer.

SST
09950-60010  (09951-00300, 09951-00520, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

11.20 to 12.20 mm (0.4410 to 0.4803 in.)



b.

Lightly apply MP grease to the lip of the oil seal.


Hide 32.INSTALL FRONT BEARING RETAINER

a.
D026036
2.594,0.833 2.302,0.833 true 2.698,0.75 2.854,0.896 0.156,0.146 10 false *1
*1 Seal Packing


Apply seal packing to the bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



b.
D025950

Install the front bearing retainer to the transmission case with the 8 bolts.

Torque:
17 N*m (168 kgf*cm, 12 ft.*lbf)


c.

Check that the input shaft and output shaft rotate smoothly.


Hide 33.INSTALL TRANSFER ADAPTER OIL SEAL

a.
D029118
1.208,1.354 1.823,0.167 1.823,0.167 1.083,1.115 true 1.885,0.052 2.219,0.25 0.333,0.198 10 false SST

Using SST and a hammer, tap in a new oil seal to the transfer adapter.

SST
09710-30050  
09950-70010  (09951-07100)

Oil seal depth:

45.4 to 46.4 mm (1.788 to 1.826 in.)



b.

Lightly apply MP grease to the lip of the oil seal.


Hide 34.INSTALL REVERSE RESTRICT PIN

a.
D029042

Install the restrict pin to the transfer adapter.


b.
C282112

Using a 5 mm pin punch and hammer, tap in the slotted pin to the transfer adapter.


c.
D029040

Using a T40 ''TORX'' socket wrench, install the reverse restrict pin plug to the transfer adapter.

Torque:
19 N*m (188 kgf*cm, 14 ft.*lbf)


Hide 35.INSTALL OIL RECEIVER PIPE

a.
D029037

Install the oil receiver pipe to the transfer adapter.


Hide 36.INSTALL TRANSFER ADAPTER

a.
D029067
2.583,0.5 2.938,0.365 true 2.979,0.271 3.167,0.448 0.188,0.177 10 false *1
*1 Seal Packing


Apply seal packing to the transfer adapter as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



b.
D029119

Using a plastic-faced hammer, tap the transfer adapter to attach it to the transmission case.


c.
C282109

Install the transfer adapter to the transmission case with the 10 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 37.INSTALL SHIFT AND SELECT LEVER SHAFT

a.
D029039

Install the shift and select lever shaft and shift lever housing to the transfer adapter.


b.
D029038

Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the transfer adapter.


Hide 38.INSTALL TRANSFER CONTROL SHIFT LEVER RETAINER

a.
D029035

Install the select return spring on the shift lever retainer.


b.
C282103

Install the shift lever retainer to the transfer adapter with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 39.INSTALL CONTROL SHIFT LEVER RETAINER

a.
C282102

Install the control shift lever retainer and a new oil deflector.


b.

Install the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 40.INSTALL RESTRICT PIN

a.
D029031
1.458,0.594 1.135,0.313 false 1.448,1.865 1.177,1.958 false 0.979,0.219 1.208,0.427 0.229,0.208 10 true *a 0.979,1.917 1.208,2.125 0.229,0.208 10 true *b
*a Blue
*b Red


Install the 2 restrict pins.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 41.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
D029030
2.531,1.875 1.854,1.031 true 2.448,1.927 2.792,2.135 0.344,0.208 10 false SST

Using SST, install a new gasket and the back-up light switch to the transmission case.

SST
09817-16011  

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 42.INSTALL CLUTCH HOUSING

a.
D029028

Install the clutch housing to the transmission case with the 9 bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 43.INSTALL RELEASE FORK SUPPORT

Hide 44.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

Hide 45.INSTALL CLUTCH RELEASE FORK BOOT

Hide 46.INSTALL DRAIN PLUG

a.

Install a new gasket and the drain plug to the transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 47.INSTALL FILLER PLUG

a.

Install a new gasket and the filler plug to the transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)