Home › Drivetrain › VF2A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY
RM1840EF _52 Drivetrain _009616 VF2A TRANSFER / 4WD / AWD _0052537 TRANSFER ASSEMBLY A

VF2A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE TRANSFER INDICATOR SWITCH (4WD POSITION)

Hide 2.REMOVE TRANSFER INDICATOR SWITCH (L4 POSITION) (for Automatic Transmission or Manual Transmission w/ ABS)

Hide 3.REMOVE TRANSFER INDICATOR SWITCH (NEUTRAL POSITION) (for Automatic Transmission)

Hide 4.REMOVE TRANSFER GEAR SHIFT HEAD

a.
C237910C01
1.896,0.948 2,0.5 false 1.448,0.833 1.552,0.375 false 1.875,2.896 1.99,2.438 false 0.958,3.01 1.073,2.563 false 1.323,2.396 0.469,1.667 0.469,1.667 1.167,1.01 true 0.24,1.573 0.5,1.781 0.26,0.208 10 false *1 0.854,3.052 1.115,3.26 0.26,0.208 10 false *3 1.948,0.302 2.208,0.51 0.26,0.208 10 false *4 1.76,2.927 2.021,3.135 0.26,0.208 10 false *5 1.49,0.188 1.75,0.396 0.26,0.208 10 false *2
*1 Slotted Pin
*2 No. 1 Gear Shift Head
*3 No. 2 Gear Shift Head
*4 Front Drive Shift Fork Shaft
*5 High and Low Shift Fork Shaft


Using a pin punch and hammer, remove the 2 slotted pins from the No. 1 and No. 2 gear shift heads.


b.

Remove the No. 1 and No. 2 gear shift heads from the front drive shift fork shaft and the high and low shift fork shaft.


Hide 5.REMOVE TRANSFER CASE COVER SUB-ASSEMBLY

a.
C111617

Remove the 4 bolts and transfer case cover sub-assembly.


Hide 6.REMOVE BREATHER OIL DEFLECTOR

Hide 7.REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY

a.
C111638

Remove the 5 bolts and transfer bearing retainer sub-assembly.

HINT:

If necessary, tap the bearing retainer with a plastic-faced hammer to remove it.



Hide 8.REMOVE TRANSFER BEARING RETAINER OIL SEAL

a.

Using a screwdriver and hammer, tap out the transfer bearing retainer oil seal from the bearing retainer.

NOTICE:

Be careful not to damage the oil seal and bearing retainer contact surfaces.



Hide 9.REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Using a chisel and hammer, loosen the staked part of the lock nut.


b.
F043429
1.198,0.854 0.719,0.854 0.719,0.854 0.719,1.729 true 0.594,1.75 0.979,1.948 0.385,0.198 10 false SST

Using SST to hold the companion flange, remove the lock nut.

SST
09330-00021  


c.
F043430
2.229,1.708 2.604,1.708 false 2.667,1.615 3.052,1.813 0.385,0.198 10 false SST

Using SST, remove the front output shaft companion flange sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


d.

Using a screwdriver and hammer, tap out the oil seal from the companion flange.

NOTICE:

Be careful not to damage the oil seal and companion flange contact surfaces.



Hide 11.REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Remove the rear output shaft companion flange sub-assembly in the same way as the front output shaft companion flange.

SST
09330-00021  
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


b.

Using a screwdriver and hammer, tap out the oil seal from the companion flange.

NOTICE:

Be careful not to damage the oil seal and companion flange contact surfaces.



Hide 14.REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

a.

Remove the 5 bolts and extension housing.

HINT:

If necessary, tap the extension housing with a plastic-faced hammer to remove it.



Hide 15.REMOVE TRANSFER OUTPUT SHAFT WASHER

a.

Remove the 2 transfer output shaft washers.


Hide 16.REMOVE TRANSFER SPEEDOMETER DRIVE GEAR

a.

Remove the transfer speedometer drive gear and ball.


Hide 17.REMOVE REAR TRANSFER CASE

a.
G039426

Remove the 12 bolts and clamp.


b.

Remove the rear transfer case.

HINT:

If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



Hide 18.REMOVE FRONT TRANSFER DRIVE SHIFT FORK SHAFT

a.
C111621

Using a hexagon wrench, remove the 2 plugs.


b.

Using a magnet hand, remove the 2 springs and 2 balls from the holes.


c.

Mount the rear transfer case in a vise.

NOTICE:

Place aluminum plates on the vise to prevent damage to the rear transfer case.



d.
C111622

Using a pin punch and hammer, tap out the 2 slotted pins from the No. 2 transfer gear shift fork and shift shaft stopper.


e.
C111623

Hold the front transfer drive shift fork shaft in place by hand when removing the pin punch.


f.
C237911

Remove the front transfer drive shift fork shaft, stopper, compression spring, No. 1 gear shift fork and shift shaft stopper.


g.
C111625

Using a magnet hand, remove the straight pin.


Hide 19.REMOVE TRANSFER HIGH AND LOW SHIFT FORK SHAFT

a.
C111626

Remove the transfer high and low shift fork shaft and No. 2 transfer gear shift fork.


Hide 20.REMOVE REAR TRANSFER OUTPUT SHAFT, FRONT TRANSFER DRIVE CHAIN AND TRANSFER DRIVEN SPROCKET

a.
C111627

Using a snap ring expander, remove the snap ring.


b.
C237912

Using a plastic-faced hammer, carefully tap the rear transfer case, and remove the rear transfer output shaft together with the front transfer drive chain and transfer driven sprocket.


c.

Remove the rear transfer output shaft and transfer driven sprocket from the front transfer drive chain.


Hide 21.REMOVE TRANSFER DRIVEN SPROCKET BEARING

a.
C216518
2.714,1.323 3.073,1.497 0.359,0.173 10 SST 2.313,2.056 2.46,1.406 false 2.46,1.406 2.67,1.406 false

Using SST and a press, press out the transfer driven sprocket bearing.

SST
09555-55010  

NOTICE:

Be careful not to drop or damage the driven sprocket.



Hide 22.REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING

a.
C216519
2.785,1.381 3.159,1.591 0.374,0.211 10 SST 2.365,2.063 2.524,1.466 false 2.524,1.466 2.743,1.466 false

Using SST, a press and a steel bar, press out the transfer input gear radial ball bearing.

SST
09555-55010  

NOTICE:

Be careful not to damage the driven sprocket.



Hide 23.REMOVE FILLER PLUG

a.

Remove the filler plug and gasket.


Hide 24.REMOVE DRAIN PLUG

a.

Remove the drain plug and gasket.


Hide 25.REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.
C237913

Remove the 3 bolts and transfer oil separator sub-assembly.


Hide 26.REMOVE TRANSFER CASE MAGNET

Hide 27.REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY

a.
C281504

Remove the 3 bolts and transfer oil pump body sub-assembly.


Hide 28.REMOVE TRANSFER OIL PUMP BODY O-RING

a.

Using a screwdriver with its tip wrapped with protective tape, pry out the transfer oil pump body O-ring from the oil pump body.

NOTICE:
C237914

Be careful not to damage the oil pump body.



Hide 29.REMOVE TRANSFER OIL PUMP GEAR

a.
F043448

Remove the nut and transfer oil pump gear.


Hide 30.REMOVE FRONT TRANSFER DRIVE CLUTCH SYNCHRONIZER RING (for Manual Transmission)

a.
C111629

Remove the front transfer drive clutch synchronizer ring from the transfer input shaft.


Hide 31.REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT

a.
F043449

Using a snap ring expander, remove the snap ring.


b.
C111630

Remove the transfer low planetary gear assembly together with the transfer input shaft.


Hide 32.REMOVE TRANSFER CASE PLUG

a.
F043455

Remove the transfer case plug, compression spring and pin from the front transfer case.


Hide 33.REMOVE TRANSFER LOW PLANETARY RING GEAR

a.
C237915

Using a screwdriver with its tip wrapped with protective tape, pry out the snap ring.

NOTICE:

Be careful not to damage the front transfer case.



b.

Remove the transfer low planetary ring gear from the front transfer case.


Hide 34.REMOVE TRANSFER CASE OIL SEAL

a.

Using a screwdriver and hammer, tap out the 2 transfer case oil seals.

NOTICE:

Be careful not to damage the oil seal and front transfer case contact surfaces.



Hide 35.REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE

a.
C237916

Using a screwdriver with its tip wrapped with protective tape, pry out the snap ring.

NOTICE:

Be careful not to damage the transfer low planetary gear assembly.



b.
C111632

Remove the transfer low planetary gear spline piece from the transfer low planetary gear assembly.


Hide 36.REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

C111633

Hide 37.REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

a.
C111634

Using a snap ring expander, remove the transfer input gear stopper shaft snap ring.


Hide 38.REMOVE TRANSFER INPUT GEAR STOPPER

a.

Remove the transfer input gear stopper.


b.

Using a magnet hand, remove the transfer input gear stopper ball from the transfer input shaft.


c.

Remove the manual transfer planetary carrier washer.


Hide 39.REMOVE TRANSFER INPUT SHAFT

a.

Remove the transfer input shaft, transfer low planetary gear bearing and No. 1 transfer thrust bearing race from the transfer low planetary gear assembly.


Hide 40.REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING

a.

Remove the 2 No. 1 transfer input shaft seal rings from the transfer input shaft.


Hide 41.REMOVE TRANSFER INPUT SHAFT BEARING

a.

Using a snap ring expander, remove the snap ring.


b.
C216520
2.729,2.094 2.948,2.094 false 2.24,2.146 2.729,1.354 true 2.719,1.365 2.208,1.708 false 3,2.021 3.344,2.229 0.344,0.208 10 false SST 2.771,1.26 3.115,1.469 0.344,0.208 10 false SST

Using SST and a press, press out the transfer input shaft bearing.

SST
09555-55010  
09950-70010  (09951-07150)
09950-60020  (09951-00750)

NOTICE:

Be careful not to drop or damage the transfer low planetary gear.



Hide 42.REMOVE TRANSFER LOW PLANETARY GEAR BEARING

a.
F043526
2.063,1.396 2.625,1.396 2.625,1.396 2.625,1.573 true 2.521,1.625 2.979,1.823 0.458,0.198 10 false SST

Using SST, remove the transfer low planetary gear bearing.

SST
09612-65014  (09612-01030, 09612-01050)

NOTICE:

Hook SST securely between the bearing and transfer low planetary gear.



Hide 43.REMOVE TRANSFER CLUTCH HUB

a.
C111645

Using a snap ring expander, remove the snap ring.


b.

Remove the high and low clutch sleeve.


c.

for Manual Transmission:

Remove the 2 shifting key springs and 3 shifting keys.


d.

Using a press, press out the transfer clutch hub.

NOTICE:

Be careful not to drop or damage the rear transfer output shaft.



e.

for Manual Transmission:

Using a screwdriver and hammer, remove the key retainer from the rear transfer output shaft.


Hide 44.REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C216521
2.333,2.031 2.427,1.292 2.427,1.292 2.615,1.292 false 2.688,1.198 3.146,1.396 0.458,0.198 10 false SST

Using SST and a press, press out the rear transfer output shaft radial ball bearing from the rear transfer output shaft.

SST
09555-55010  

NOTICE:

Be careful not to drop or damage the rear transfer output shaft.



b.

Remove the spacer and ball.


c.

Remove the transfer drive sprocket sub-assembly together with the front drive clutch sleeve.


d.

Remove the needle roller bearing.


e.

Remove the front drive synchronizer ring.


f.

Remove the front drive clutch sleeve, 2 shifting key springs and 3 shifting keys from the transfer drive sprocket sub-assembly.