Home › Drivetrain › VF2A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY › 2011.10–2014.10
RM1840EF _52 Drivetrain _009616 VF2A TRANSFER / 4WD / AWD _0052537 TRANSFER ASSEMBLY A

VF2A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C281556C01
1.417,3.917 2.323,3.406 2.323,3.406 2.031,3.917 true 2.333,3.406 2.542,3.406 false 2.615,3.302 2.927,3.5 0.313,0.198 10 false *a
*a Shifting key spring opening


Apply gear oil to the connecting areas of the front drive clutch sleeve and transfer drive sprocket sub-assembly.


b.

Install the front drive clutch sleeve, 3 shifting keys and 2 shifting key springs to the transfer drive sprocket sub-assembly.

NOTICE:
·

Install the front drive clutch sleeve in the correct direction.

·

Install the shifting key springs so that their openings do not overlap as shown in the illustration.

·

Make sure that the shifting key springs are firmly connected to the shifting keys.

·

Make sure that the front drive clutch sleeve and transfer drive sprocket sub-assembly move smoothly.




c.

Apply gear oil to the taper cone side of the front transfer drive clutch synchronizer ring and rear transfer output shaft.


d.
C237917

Install front transfer drive clutch synchronizer ring to the transfer drive sprocket sub-assembly with front drive clutch sleeve.


e.

Apply gear oil to the needle roller bearing, and then install it to the transfer drive sprocket sub-assembly with front drive clutch sleeve.


f.

Install the transfer drive sprocket sub-assembly with front drive clutch sleeve to the rear transfer output shaft.


g.

Install the ball. Then install the spacer so that the spacer is aligned with the ball.


Hide 2.INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING

a.

Apply gear oil to the connecting areas of the rear transfer output shaft and rear transfer output shaft radial ball bearing.


b.
C217381C01
1.563,0.979 1.177,0.75 false 1.177,0.75 1.615,1.208 false 3.167,0.885 3.323,0.885 3.323,0.885 3.323,0.448 true 3.323,0.448 3.031,0.448 true 3.188,0.885 3.188,0.906 3.188,0.906 3.135,0.885 false 3.135,0.885 3.188,0.865 3.188,0.865 3.188,0.885 false 0.885,0.635 1.208,0.844 0.323,0.208 10 false SST 2.823,0.354 3.042,0.573 0.219,0.219 10 false *1
*1 Groove


Using SST and a press, press in a new rear transfer output shaft radial ball bearing to the rear transfer output shaft.

NOTICE:

Install the bearing in the correct direction.


SST
09316-60011  (09316-00011, 09316-00071)


Hide 3.CHECK TRANSFER DRIVE SPROCKET THRUST CLEARANCE

a.
C111644

Using a feeler gauge, measure the thrust clearance.

Standard thrust clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


Maximum thrust clearance:

0.25 mm (0.00984 in.)


If the thrust clearance is more than the maximum, replace the transfer drive sprocket sub-assembly.


Hide 4.INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
C281557C01
1.417,3.896 2.51,3.656 2.51,3.656 2.01,4.083 true 2.594,3.552 2.906,3.75 0.313,0.198 10 false *a
*a Shifting key spring opening


Apply gear oil to the connecting areas of the transfer high and low clutch sleeve and transfer clutch hub.


b.

for Automatic Transmission:

Install the transfer high and low clutch sleeve to the transfer clutch hub.

NOTICE:
·

Install the transfer high and low clutch sleeve in the correct direction.

·

Make sure that the transfer high and low clutch sleeve and transfer clutch hub move smoothly.




c.

for Manual Transmission:

Install the transfer high and low clutch sleeve, 3 shifting keys and 2 shifting key springs to the transfer clutch hub.

NOTICE:
·

Install the transfer high and low clutch sleeve in the correct direction.

·

Install the shifting key springs so that their openings do not overlap as shown in the illustration.

·

Make sure that the shifting key springs are firmly connected to the shifting keys.

·

Make sure that the transfer high and low clutch sleeve and transfer clutch hub move smoothly.




Hide 5.INSTALL TRANSFER CLUTCH HUB

a.

M/T:

i.

Apply gear oil to the connecting areas of a new key retainer and the output shaft.


ii.
C111653N02
1.563,1.135 1.792,1.135 false 1.875,1.052 2.229,1.219 0.354,0.167 10 false SST

Using SST and a hammer, tap in the key retainer.

SST
09316-60011  (09316-00011)

NOTICE:

Be careful not to deform or damage the key retainer.




b.

Apply gear oil to the connecting areas of the clutch hub and output shaft.


c.
C111654

Using a press, press in the transfer clutch hub.


Hide 6.INSTALL TRANSFER OUTPUT SHAFT SNAP RING

a.
C111655

Select a new snap ring that allows the minimum axial free play.

Snap Ring Thickness:
Mark Specified Condition
K 2.00 to 2.05 mm (0.0788 to 0.0807 in.)
L 2.05 to 2.10 mm (0.0808 to 0.0826 in.)
A 2.10 to 2.15 mm (0.0827 to 0.0846 in.)
B 2.15 to 2.20 mm (0.0847 to 0.0866 in.)
C 2.20 to 2.25 mm (0.0867 to 0.0885 in.)
D 2.25 to 2.30 mm (0.0886 to 0.0905 in.)
E 2.30 to 2.35 mm (0.0906 to 0.0925 in.)
F 2.35 to 2.40 mm (0.0926 to 0.0944 in.)
G 2.40 to 2.45 mm (0.0945 to 0.0964 in.)
H 2.45 to 2.50 mm (0.0965 to 0.0984 in.)
J 2.50 to 2.55 mm (0.0985 to 0.1004 in.)



b.

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 7.INSTALL TRANSFER LOW PLANETARY GEAR BEARING

a.
C111656N02
2.667,0.938 2.458,0.938 2.458,0.938 2.458,1.635 true 2.573,1.094 2.458,1.094 false 2.302,1.635 2.656,1.802 0.354,0.167 10 false SST

Using SST and a press, press in a new transfer low planetary gear bearing.

SST
09950-60010  (09951-00570)
09950-70010  (09951-07100)

Standard depth:

8.2 to 8.8 mm (0.323 to 0.346 in.)



Hide 8.INSTALL TRANSFER INPUT SHAFT BEARING

a.
C111657N02
0.927,0.792 0.625,0.792 false 1.115,0.427 0.802,0.427 0.802,0.427 0.802,0.792 false 1.313,1.594 1.833,1.594 1.833,1.594 1.833,1.667 true 1.708,1.667 2.021,1.833 0.313,0.167 10 false SST 0.26,0.698 0.573,0.865 0.313,0.167 10 false SST

Using SST and a press, press in a new transfer input shaft bearing with the groove facing forward.

SST
09223-15020  
09515-30010  
09950-70010  (09951-07100)


Hide 9.INSTALL TRANSFER INPUT BEARING SHAFT SNAP RING

a.
C111658

Select a new snap ring that allows 0.1 mm (0.00393 in.) or less of axial free play.

Snap Ring Thickness:
Mark Specified Condition
1 1.45 to 1.50 mm (0.0571 to 0.0590 in.)
2 1.50 to 1.55 mm (0.0591 to 0.0610 in.)
3 1.55 to 1.60 mm (0.0611 to 0.0629 in.)
4 1.60 to 1.65 mm (0.0630 to 0.0649 in.)
5 1.65 to 1.70 mm (0.0650 to 0.0669 in.)



b.

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 10.INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

a.
C229867

Apply gear oil to the 2 new No. 1 transfer input shaft seal rings, and then install them to the transfer input shaft.

NOTICE:

When installing the seal ring, make sure not to expand it so that its inner diameter exceeds 65 mm (2.55 in.).



Hide 11.INSTALL TRANSFER INPUT SHAFT

a.
C237918C01
2.208,1.427 2.208,2.583 false 1.802,1.625 1.802,2.604 false 2.125,2.646 2.365,2.865 0.24,0.219 10 false *1 1.729,2.677 2.052,2.896 0.323,0.219 10 false *2
*1 Transfer Low Planetary Gear Bearing
*2 No. 1 Transfer Thrust Bearing Race


Install the bearing to the transfer low planetary gear assembly.

NOTICE:

Install the bearing in the correct direction.



b.

Install the No. 1 transfer thrust bearing race to the transfer low planetary gear assembly.


c.

Apply gear oil to the contact surfaces of the transfer input shaft and transfer low planetary gear assembly.


d.

Install the transfer input shaft to the transfer low planetary gear assembly.


e.
C233253

Apply gear oil to the manual transfer planetary carrier washer.


f.

Install the manual transfer planetary carrier washer to the transfer low planetary gear assembly.


g.

Install the transfer input gear stopper ball to the transfer input shaft.


h.

Install the transfer input gear stopper to the transfer input shaft.


Hide 12.INSTALL TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

a.
F043514

Select a new transfer input gear stopper shaft snap ring that allows 0.05 to 0.15 mm (0.00197 to 0.00590 in.) of axial free play.

Snap Ring Thickness:
Mark Specified Condition
A 2.10 to 2.15 mm (0.0827 to 0.0846 in.)
B 2.15 to 2.20 mm (0.0847 to 0.0866 in.)
C 2.20 to 2.25 mm (0.0867 to 0.0885 in.)
D 2.25 to 2.30 mm (0.0886 to 0.0905 in.)
E 2.30 to 2.35 mm (0.0906 to 0.0925 in.)
F 2.35 to 2.40 mm (0.0926 to 0.0944 in.)
G 2.40 to 2.45 mm (0.0945 to 0.0964 in.)
H 2.45 to 2.50 mm (0.0965 to 0.0984 in.)
J 2.50 to 2.55 mm (0.0985 to 0.100 in.)
K 2.55 to 2.60 mm (0.101 to 0.102 in.)
L 2.60 to 2.65 mm (0.103 to 0.104 in.)
M 2.65 to 2.70 mm (0.105 to 0.106 in.)
N 2.70 to 2.75 mm (0.107 to 0.108 in.)
P 2.75 to 2.80 mm (0.109 to 0.110 in.)
Q 2.80 to 2.85 mm (0.111 to 0.112 in.)
R 2.85 to 2.90 mm (0.113 to 0.114 in.)
S 2.90 to 2.95 mm (0.115 to 0.116 in.)
T 2.95 to 3.00 mm (0.117 to 0.118 in.)
U 3.00 to 3.05 mm (0.119 to 0.120 in.)



b.

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 13.INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING

a.
C111633

Apply gear oil to the front transfer output shaft needle roller bearing, and then install it to the transfer low planetary gear assembly.


Hide 14.INSTALL TRANSFER LOW PLANETARY GEAR SPLINE PIECE

a.
C111632

Install the transfer low planetary gear spline piece to the transfer low planetary gear assembly.


b.
C237916

Using a screwdriver with its tip wrapped with protective tape, install the snap ring.

NOTICE:

Be careful not to damage the transfer low planetary gear assembly.



Hide 15.INSTALL TRANSFER CASE OIL SEAL

a.
C111659N03
0.76,1.229 0.271,1.229 0.271,1.229 0.271,1.469 true 0.135,1.49 0.479,1.656 0.344,0.167 10 false SST

Using SST and a hammer, tap in 2 new transfer case oil seals until their surfaces are flush with the case upper surface.

SST
09304-12012  

Standard depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)


NOTICE:

Be careful not to damage the front transfer case.



b.

Coat the lip of each oil seal with MP grease.


Hide 16.INSTALL TRANSFER LOW PLANETARY RING GEAR

a.
C237919

Install the transfer low planetary ring gear to the front transfer case.

NOTICE:

Install the ring gear in the correct direction.



b.
C237915

Using a screwdriver with its tip wrapped with protective tape, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 17.INSTALL TRANSFER CASE PLUG

a.

Install the pin and compression spring to the front transfer case.


b.
F043455

Apply adhesive to the threads of the transfer case plug, and then install it to the front transfer case.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 18.INSTALL TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT

a.
C111630

Install the transfer low planetary gear assembly with transfer input shaft.

HINT:

If necessary, heat the front case to about 50 to 80°C (122 to 176°F).



b.
F043449

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 19.INSTALL FRONT TRANSFER DRIVE CLUTCH SYNCHRONIZER RING

a.
C111629

Apply gear oil to the front transfer drive clutch synchronizer ring taper cone side, and then install it to the transfer input shaft.


Hide 20.INSTALL TRANSFER OIL PUMP GEAR

a.
F043448

Apply gear oil to the sliding surface of the transfer oil pump gear.


b.

Install the transfer oil pump gear.


Hide 21.INSTALL TRANSFER OIL PUMP BODY O-RING

a.
C281506

Coat a new O-ring with gear oil and install it to the transfer oil pump body.


Hide 22.INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY

a.
C281504

Install the transfer oil pump body sub-assembly with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 23.INSTALL TRANSFER CASE MAGNET

Hide 24.INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.
C237913

Install the oil separator with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 25.INSTALL FILLER PLUG

a.

Install a new gasket and the filler plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 26.INSTALL DRAIN PLUG

a.

Install a new gasket and the drain plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 27.INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING

a.
C216377N03
1.917,1.531 1.427,1.135 true 1.427,1.135 1.115,1.135 true 0.708,1.031 1.083,1.229 0.375,0.198 10 false SST

Apply gear oil to the contact surfaces of a new transfer input gear radial ball bearing and the transfer driven sprocket.


b.

Using SST and a press, press in the transfer input gear radial ball bearing.

SST
09316-60011  (09316-00031)

NOTICE:

After press-fitting the bearing to the transfer driven sprocket, check that the bearing moves smoothly.



Hide 28.INSTALL TRANSFER DRIVEN SPROCKET BEARING

a.
C216378N02
2.24,2.573 1.26,2.573 true 0.948,2.49 1.323,2.708 0.375,0.219 10 false SST

Apply gear oil to the contact surfaces of a new transfer driven sprocket bearing and transfer driven sprocket.


b.

Using SST and a press, press in the transfer driven sprocket bearing.

SST
09316-60011  (09316-00071)

NOTICE:

After press-fitting the bearing to the transfer driven sprocket, check that the bearing moves smoothly.



Hide 29.INSTALL REAR TRANSFER OUTPUT SHAFT, TRANSFER FRONT DRIVE CHAIN AND TRANSFER DRIVEN SPROCKET

a.
C234757C01
2.854,0.948 2.542,1.74 true 2.406,1.781 2.635,1.979 0.229,0.198 10 false *1
*1 Aluminum Plate


Mount the rear transfer case in a vise.

NOTICE:

Place aluminum plates on the vise to prevent damage to the rear transfer case.



b.

Install the rear transfer output shaft and transfer driven sprocket to the front drive chain.


c.

Install the rear transfer output shaft together with the front transfer drive chain and transfer driven sprocket to the rear transfer case.

NOTICE:

When installing the rear transfer output shaft, make sure that the installation of the synchronizer ring, sleeve and shifting keys is not affected.


HINT:

Check that the output shaft and driven sprocket turn smoothly.

If necessary, heat the rear case to approximately 50 to 80°C (122 to 176°F).



d.
C111627

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 30.INSTALL TRANSFER HIGH AND LOW SHIFT FORK SHAFT

a.
C237921

Apply gear oil to the connecting areas of the transfer high and low shift fork shaft and each part.


b.

Install the transfer high and low shift fork shaft and No. 2 transfer gear shift fork.

NOTICE:

Install the transfer high and low shift fork shaft and No. 2 transfer gear shift fork in the correct directions.



c.

Install the ball and spring to the hole.


d.

Apply adhesive to the threads of the plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.

Using a hexagon wrench, install the plug.

Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 31.INSTALL FRONT TRANSFER DRIVE SHIFT FORK SHAFT

a.
C111625

Apply gear oil to the straight pin and install it to the hole of the rear transfer case.


b.
C237920

Apply gear oil to the connecting areas of the front transfer drive shift fork shaft and each part.


c.

Install the front transfer drive shift fork shaft, spring, No. 1 transfer gear shift fork and shift shaft stopper.

NOTICE:

Install the front transfer drive shift fork shaft, No. 1 transfer gear shift fork and shift shaft stopper in the correct directions.



d.
C281507N01
1.958,2.948 2.115,3.146 0.156,0.198 10 false A 1.333,4 1.49,4.198 0.156,0.198 10 false A

Using a pin punch and hammer, install the 2 slotted pins.

NOTICE:

When installing the slotted pins, make sure that groove A of the pin is facing in the same direction as the shaft.



e.

Install the ball and spring to the hole of the rear transfer case.


f.

Apply adhesive to the threads of the plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



g.

Using a hexagon wrench, install the plug.

Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 32.INSTALL REAR TRANSFER CASE

a.

Remove any old seal packing and be careful not to spill oil on the contact surfaces of the front transfer case and rear transfer case.


b.
F043488C02
2.125,0.729 2.479,0.375 2.479,0.375 2.625,0.375 false 2.688,0.271 2.885,0.469 0.198,0.198 10 false *1
*1 Seal Packing


Apply seal packing to the rear case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



c.
G039426

Install the clamp and rear case with the 12 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

Tighten the bolts of the rear case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 33.INSTALL TRANSFER SPEEDOMETER DRIVE GEAR

a.

Install the ball and transfer speedometer drive gear to the rear transfer output shaft.


Hide 34.INSTALL TRANSFER OUTPUT SHAFT WASHER

a.

Install the 2 transfer output washers to the rear transfer output shaft.


Hide 35.INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

a.

Remove any old seal packing and be careful not to spill oil on the contact surfaces of the transfer extension housing sub-assembly and rear transfer case.


b.
F043489C01
2.5,1.042 2.719,0.833 2.719,0.833 2.865,0.833 true 2.906,0.729 3.073,0.927 0.167,0.198 10 false *1
*1 Seal Packing


Apply seal packing to the transfer extension housing sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



c.

Apply adhesive to the threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Install the transfer extension housing sub-assembly with the 5 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the bolts of the transfer extension housing sub-assembly within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 39.INSTALL FRONT OUTPUT SHAFT COMPANIONFLANGE SUB-ASSEMBLY

a.
F043517N02
1.01,0.938 0.448,0.75 0.448,0.75 0.979,1.531 true 0.135,0.667 0.594,0.875 0.458,0.208 10 false SST

Using SST and a hammer, tap in a new oil seal to the front output shaft companion flange sub-assembly.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07100)

NOTICE:

Be careful not to damage the companion flange.



b.

Apply gear oil to the connecting areas of the front output shaft companion flange sub-assembly and transfer driven sprocket.


c.

Install the front output shaft companion flange sub-assembly to the transfer driven sprocket.


d.

Using SST to hold the companion flange, install a new lock nut.

SST
09330-00021  

Torque:
118 N*m (1203 kgf*cm, 87 ft.*lbf)


e.
F050151C02
0.802,0.25 1,0.448 0.198,0.198 10 false *a 0.802,1.885 0.99,2.083 0.188,0.198 10 false *b
*a CORRECT
*b INCORRECT


Using a chisel and hammer, stake the lock nut.

NOTICE:
·

Securely stake the shaft to the lock nut groove.

·

Be careful not to damage parts around the lock nut.

·

Do not apply excessive force to the shaft.




Hide 40.INSTALL REAR OUTPUT SHAFT COMPANIONFLANGE SUB-ASSEMBLY

a.
F043517N02
1.01,0.938 0.448,0.75 0.448,0.75 0.979,1.531 true 0.135,0.667 0.594,0.875 0.458,0.208 10 false SST

Using SST and a hammer, tap in a new oil seal to the rear output shaft companion flange sub-assembly.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07100)

NOTICE:

Be careful not to damage the companion flange.



b.

Apply gear oil to the connecting areas of the rear output shaft companion flange and rear transfer output shaft.


c.

Using SST, install the rear output shaft companion flange sub-assembly in the same way as the front output shaft companion flange.

SST
09330-00021  

Torque:
118 N*m (1203 kgf*cm, 87 ft.*lbf)


Hide 41.INSTALL BREATHER OIL DEFLECTOR SUB-ASSEMBLY

Hide 42.INSTALL TRANSFER CASE COVER SUB-ASSEMBLY

a.

Install the transfer case cover sub-assembly with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 43.INSTALL TRANSFER BEARING RETAINER OIL SEAL

a.
F043518N02
0.948,0.927 0.479,0.677 true 0.479,0.677 0.844,1.333 true 0.177,0.594 0.469,0.781 0.292,0.188 10 false SST

Using SST and a hammer, tap in a new transfer bearing retainer oil seal until its surface is flush with the bearing retainer upper surface.

SST
09950-60010  (09951-00590)
09950-70010  (09951-07100)

NOTICE:

Be careful not to damage the bearing retainer.



b.

Coat the lip of the oil seal with MP grease.


Hide 44.INSTALL TRANSFER BEARING RETAINER SUB-ASSEMBLY

a.

Remove any old seal packing and be careful not to spill oil on the contact surfaces of the transfer bearing retainer sub-assembly and front transfer case.


b.
F043490C01
2.375,0.677 2.615,0.448 2.615,0.448 2.719,0.448 true 2.771,0.354 2.958,0.552 0.188,0.198 10 false *1
*1 Seal Packing


Apply seal packing to the transfer bearing retainer sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



c.

Apply adhesive to the bolt threads.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Install the transfer bearing retainer sub-assembly with the 5 bolts.

Torque:
12 N*m (117 kgf*cm, 8 ft.*lbf)

NOTICE:

Tighten the bolts of the bearing retainer within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 45.INSTALL TRANSFER GEAR SHIFT HEAD

a.
C237910C01
1.896,0.948 2,0.5 false 1.448,0.833 1.552,0.375 false 1.875,2.896 1.99,2.438 false 0.958,3.01 1.073,2.563 false 1.323,2.396 0.469,1.667 0.469,1.667 1.167,1.01 true 0.24,1.573 0.5,1.781 0.26,0.208 10 false *1 0.854,3.052 1.115,3.26 0.26,0.208 10 false *3 1.948,0.302 2.208,0.51 0.26,0.208 10 false *4 1.76,2.927 2.021,3.135 0.26,0.208 10 false *5 1.49,0.188 1.75,0.396 0.26,0.208 10 false *2
*1 Slotted Pin
*2 No. 1 Gear Shift Head
*3 No. 2 Gear Shift Head
*4 Front Drive Shift Fork Shaft
*5 High and Low Shift Fork Shaft


Install the No. 1 and No. 2 transfer gear shift heads to the front transfer drive shift fork shaft and transfer high and low shift fork shaft.


b.
F050152N01
2.073,1.25 2.229,1.448 0.156,0.198 10 false A 1.25,2.771 1.406,2.969 0.156,0.198 10 false A

Using a pin punch and hammer, tap in the 2 slotted pins to the No. 1 and No. 2 transfer gear shift heads.

NOTICE:

When installing the slotted pins, make sure the pin groove labeled A is facing in the same direction as the shaft.



Hide 46.INSTALL TRANSFER INDICATOR SWITCH (NEUTRAL POSITION) (for Automatic Transmission)

Hide 47.INSTALL TRANSFER INDICATOR SWITCH (L4 POSITION) (for Automatic Transmission or Manual Transmission w/ ABS)

Hide 48.INSTALL TRANSFER INDICATOR SWITCH (4WD POSITION)