Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made)
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052548 FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for both universal joint spiders.


a.
C060598

Apply MP grease to a new spider and 2 new spider bearings.

NOTICE:

Be careful not to apply too much grease.



b.

Fit the spider into the flange yoke.


c.
C281350
1.021,0.833 1.125,0.354 1.125,0.354 1.292,0.354 false 1.344,0.271 1.688,0.458 0.344,0.188 10 false SST

Using SST, install the 2 spider bearings to the spider.

SST
09332-25010  


d.
F052434

Using SST, adjust the spider bearings so that: 1) the flange yoke does not overlap the snap ring grooves of the spider bearings; 2) the grooves are as wide as possible; and 3) the groove width on both sides is the same.

SST
09332-25010  


e.

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

Standard Snap Ring Thickness:
Part No. Thickness Color
90080-52044 1.384 mm (0.0545 in.) Green
90080-52174 1.39 mm (0.0547 in.) Green
90080-52043 1.435 mm (0.0565 in.) Red
90080-52175 1.44 mm (0.0567 in.) Orange
90080-52041 1.486 mm (0.0585 in.) Black
90080-52176 1.49 mm (0.0587 in.) Black
90080-52042 1.511 mm (0.0595 in.) Copper
90080-52040 1.537 mm (0.0605 in.) Silver
90080-52177 1.54 mm (0.0606 in.) White
90080-52039 1.588 mm (0.0625 in.) Yellow
90080-52178 1.59 mm (0.0626 in.) Yellow
90080-52038 1.638 mm (0.0645 in.) Blue
90080-52179 1.64 mm (0.0646 in.) Red
90080-52180 1.69 mm (0.0665 in.) Blue


NOTICE:
·

New snap rings must be used.

·

The snap ring thickness must be the same on both ends.




f.
C282524
2.365,0.656 1.656,0.302 1.656,0.302 1.333,0.302 true 1.115,0.198 1.427,0.354 0.313,0.156 10 false *a
*a Hammering Point


Using a plastic-faced hammer, tap the flange yoke until there is no clearance between the spider bearings and snap rings.


g.

Align the matchmarks on the flange yoke and propeller shaft.


h.

Install new spider bearings on the sleeve yoke side.

HINT:

Use the procedure described above.



Hide 3.INSTALL SLIDING SHAFT BOOT

a.

Temporarily install the boot to the propeller shaft with 2 new clamps.


b.

Mount the propeller shaft in a soft vise.


c.

Coat the splines of the propeller shaft with MP grease.


d.

Align the matchmarks on the propeller shaft and sleeve yoke.


e.

Install the sleeve yoke to the propeller shaft and connect the boot.


f.
C118610
2.188,1.094 2.844,1.521 true 2.896,1.5 3.219,1.688 0.323,0.188 10 false SST

Secure one of the boot clamps to the boot.

i.

Place SST onto the boot clamp.

SST
09521-24010  


ii.

Tighten SST so that the boot clamp is pinched as shown in the illustration.

NOTICE:

Do not overtighten SST.



iii.
C118611
1.906,1.052 2.938,1.531 true 3,1.51 3.323,1.677 0.323,0.167 10 false SST

Using SST, adjust the clearance of the boot clamp.

SST
09240-00020  

Standard clearance:

0.8 mm (0.0314 in.) or less




g.

Secure the remaining boot clamp to the boot.

HINT:

Use the procedure described above.



Hide 4.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with MP grease.



C118606
0.75,1.427 0.75,0.531 0.75,0.531 1,0.531 true 4.604,1.385 4.604,0.771 4.604,0.771 4.854,0.771 true 1.073,0.438 1.344,0.604 0.271,0.167 10 false *1 4.917,0.677 5.198,0.844 0.281,0.167 10 false *2 5.729,1.854 6,2.031 0.271,0.177 10 false *1 5.719,0.865 5.979,1.073 0.26,0.208 10 false *2 2.646,0.688 2.927,0.875 0.281,0.188 10 false *b 0.177,0.115 0.479,0.302 0.302,0.188 10 false *a
*1 No. 1 Grease Fitting *2 No. 2 Grease Fitting
*a Spider grease fitting assembly direction for front propeller shaft assembly *b Rear Side