Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TASA Made)
RM1840EF _52 Drivetrain _009617 DRIVE SHAFT / PROPELLER SHAFT _0052549 PROPELLER SHAFT ASSEMBLY(for TASA Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TASA Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CENTER NO. 1 SUPPORT BEARING ASSEMBLY

a.
C118619
0.385,0.354 0.646,0.542 0.26,0.188 10 false *a
*a Front Side


Install the center support bearing to the intermediate shaft.


b.

Coat the splines of the intermediate shaft with MP grease.


c.

Install the washer.


d.
C118617
1.74,1.115 1.74,0.521 1.74,0.521 2.698,0.521 true 1.76,1.25 2.115,1.25 2.115,1.25 2.115,0.521 true 2.74,0.458 3,0.635 0.26,0.177 10 false *1
*1 Matchmark


Align the matchmarks on the center yoke and intermediate shaft, and then install the yoke to the shaft.


e.

Install the washer.


f.
C118620

Clamp the center yoke in a vise between aluminum plates and press the bearing into position by installing a new nut.

Torque:
181 N*m (1850 kgf*cm, 134 ft.*lbf)


g.

Loosen the nut.


h.

Tighten the nut again.

Torque:
82 N*m (836 kgf*cm, 60 ft.*lbf)


i.
C118621

Using a chisel and hammer, stake the lock nut.


Hide 2.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for all universal joint spiders.


a.
C060598

Apply MP grease to a new spider and 2 new spider bearings.

NOTICE:

Be careful not to apply too much grease.



b.

Fit the spider into the flange yoke.


c.
C281350
1.021,0.833 1.125,0.354 1.125,0.354 1.292,0.354 false 1.344,0.271 1.688,0.458 0.344,0.188 10 false SST

Using SST, install the spider bearings to the spider.

SST
09332-25010  


d.
F052434

Using SST, adjust the spider bearings so that: 1) the yoke does not overlap the snap ring grooves of the spider bearings; 2) the grooves are as wide as possible; and 3) the groove width on both sides is the same.

SST
09332-25010  


e.

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

Standard Snap Ring Thickness:
Part No. Thickness Color
90080-52044 1.384 mm (0.0545 in.) Green
90080-52174 1.39 mm (0.0547 in.) Green
90080-52043 1.435 mm (0.0565 in.) Purple
90080-52175 1.44 mm (0.0567 in.) Orange
90080-52041 1.486 mm (0.0585 in.) Black
90080-52176 1.49 mm (0.0587 in.) Black
90080-52042 1.511 mm (0.0595 in.) Copper
90080-52040 1.537 mm (0.0605 in.) White
90080-52177 1.54 mm (0.0606 in.) White
90080-52039 1.588 mm (0.0625 in.) Yellow
90080-52178 1.59 mm (0.0626 in.) Yellow
90080-52038 1.638 mm (0.0645 in.) Blue
90080-52179 1.64 mm (0.0646 in.) Red
90080-52180 1.69 mm (0.0665 in.) Blue
90080-52156
*
1.49 mm (0.0587 in.) -

*: For cup with grease nipple.


NOTICE:
·

New snap rings must be used.

·

The snap ring thickness must be the same on both ends.




f.
C282524
2.365,0.656 1.656,0.302 1.656,0.302 1.333,0.302 true 1.115,0.198 1.427,0.354 0.313,0.156 10 false *a
*a Hammering Point


Using a plastic-faced hammer, tap the flange yoke until there is no clearance between the spider bearings and snap rings.


g.

Align the matchmarks on the yoke and shaft (or center yoke and sleeve yoke), and install the yoke together with the spider.


h.

Install new spider bearings on the shaft side.

HINT:

Use the procedure described above.



Hide 3.INSTALL REAR SLIDING SHAFT BOOT (for 4WD)

a.

Temporarily install a new boot to the propeller shaft with 2 new clamps.


b.

Mount the propeller shaft in a soft vise.


c.

Coat the splines of the propeller shaft with MP grease.


d.

Align the matchmarks on the propeller shaft and sleeve yoke.


e.

Install the sleeve yoke to the propeller shaft and connect the boot.


f.
C118610
2.188,1.094 2.844,1.521 true 2.896,1.5 3.219,1.688 0.323,0.188 10 false SST

Secure one of the boot clamps to the boot.

i.

Place SST onto the boot clamp.

SST
09521-24010  


ii.

Tighten SST so that the boot clamp is pinched as shown in the illustration.

NOTICE:

Do not overtighten SST.



iii.
C118611
1.906,1.052 2.938,1.531 true 3,1.51 3.323,1.677 0.323,0.167 10 false SST

Using SST, adjust the clearance of the boot clamp.

SST
09240-00020  

Standard clearance:

0.8 mm (0.0314 in.) or less




g.

Secure the remaining boot clamp to the boot.

HINT:

Use the procedure described above.



Hide 4.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with MP grease.



C281388
1.74,0.906 1.74,0.688 1.74,0.688 1.906,0.688 false 4.406,0.917 4.406,0.698 4.406,0.698 4.573,0.698 false 6.167,0.917 6.167,0.698 6.167,0.698 6.333,0.698 false 1.115,3.406 1.115,3.188 1.115,3.188 1.281,3.188 false 3.135,3.406 3.135,3.188 3.135,3.188 3.302,3.188 false 6.188,3.406 6.188,3.188 6.188,3.188 6.354,3.188 false 0.438,0.813 0.75,0.969 0.313,0.156 10 false *A 0.427,3.188 0.74,3.344 0.313,0.156 10 false *B 1.958,0.594 2.271,0.75 0.313,0.156 10 false *1 4.615,0.604 4.927,0.76 0.313,0.156 10 false *2 6.385,0.615 6.698,0.771 0.313,0.156 10 false *3 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 3.885,0.198 4.198,0.354 0.313,0.156 10 false *b 3.875,2.833 4.188,2.99 0.313,0.156 10 false *b 1.917,2.021 2.229,2.177 0.313,0.156 10 false *1 2.104,2.021 2.417,2.177 0.313,0.156 10 false *2 2.292,2.021 2.604,2.177 0.313,0.156 10 false *3 6.406,3.094 6.719,3.25 0.313,0.156 10 false *3 3.354,3.094 3.667,3.25 0.313,0.156 10 false *2 1.333,3.094 1.646,3.25 0.313,0.156 10 false *1 1.917,4.625 2.229,4.781 0.313,0.156 10 false *1 2.094,4.625 2.406,4.781 0.313,0.156 10 false *2 2.271,4.625 2.583,4.781 0.313,0.156 10 false *3
*A for Pre-Runner *B for 4WD
*1 No. 1 Grease Fitting *2 No. 2 Grease Fitting
*3 No. 3 Grease Fitting - -
*a Spider grease fitting assembly direction for propeller shaft assembly *b *Rear Side