Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB(for 4WD and Pre-Runner)
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052556 FRONT AXLE HUB(for 4WD and Pre-Runner) A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE HUB OIL SEAL LH

a.
F042762

Using a brass bar and hammer, tap in a new oil seal.

NOTICE:

Do not damage the spacer.



Hide 2.INSTALL FRONT AXLE HUB INNER BEARING LH (for 4WD)

a.
C098702
1.99,0.844 2.719,0.844 false 2.802,0.74 3.188,0.948 0.385,0.208 10 false SST

Using SST and a press, press a new bearing into the axle hub.

SST
09649-17010  

NOTICE:

Insert 4 bolts into the bearing before installing the the bearing to the axle hub.



b.

w/ ABS:

Install the spacer and ABS rotor to the axle hub.


c.

w/o ABS:

Install the 2 spacers to the axle hub.


Hide 3.INSTALL FRONT AXLE HUB INNER BEARING LH (for Pre-Runner)

a.
C098702
1.99,0.844 2.719,0.844 false 2.771,0.729 3.156,0.938 0.385,0.208 10 false SST

Using SST and a press, press a new bearing into the axle hub.

SST
09649-17010  

NOTICE:

Insert 4 bolts into the bearing before installing the bearing to the axle hub.



b.

w/ ABS:

Install the sensor rotor to the axle hub.


c.

w/o ABS:

Install the spacer to the axle hub.


d.
C238290
0.896,0.844 1.094,0.844 false 1.094,0.844 1.271,1.177 false 0.531,0.74 0.906,0.927 0.375,0.188 10 false SST

Using SST, install a new adjusting nut.

SST
09607-26010  

Torque:
274 N*m (2794 kgf*cm, 202 ft.*lbf)


Hide 4.INSTALL FRONT AXLE HUB ASSEMBLY

F042759

a.

Apply MP grease to a new O-ring.


b.

Install the O-ring to the axle hub.


c.

Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 5.INSTALL FRONT AXLE SHAFT NUT LH (for 4WD)

F042732

a.

Clean the threaded parts on the drive shaft and axle shaft nut using a non-residue solvent.


b.

Install the shaft nut.

Torque:
235 N*m (2396 kgf*cm, 173 ft.*lbf)


c.

Install the adjusting cap and a new cotter pin.

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



Hide 6.INSTALL FRONT AXLE HUB GREASE CAP LH (for 4WD)

a.

Install a new grease cap to the axle hub.


Hide 9.INSTALL FRONT SPEED SENSOR LH (w/ ABS)

C282010

a.

Install the speed sensor with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Connect the 2 clamps.


c.

Install the speed sensor wire harness to the steering knuckle with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 10.INSTALL FRONT WHEEL

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)