Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052563 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C237478
1.385,1.313 0.75,0.854 0.75,0.854 0.563,0.854 true 0.219,0.76 0.521,0.917 0.302,0.156 10 false SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Backlash:

0.11 to 0.21 mm (0.00433 to 0.00826 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 2.INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C236648
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Item Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.



Hide 3.REMOVE DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY

a.
C237694

Remove the 4 bolts.


b.

Using a hammer, pry out the actuator from the differential tube.


Hide 4.REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

a.
C237479

Remove the 4 bolts.


b.

Using a plastic-faced hammer, tap out the differential tube.


Hide 5.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH

a.
C282341
1.302,0.885 1.667,0.521 1.667,0.521 1.906,0.521 false 1.99,0.427 2.448,0.625 0.458,0.198 10 false SST

Using SST, tap out the oil seal.

SST
09308-00010  


Hide 6.REMOVE DIFFERENTIAL CLUTCH SLEEVE

a.

Remove the differential clutch sleeve.


Hide 7.REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY

a.

Remove the snap ring from the inter shaft.


b.
C282342
0.729,0.417 1.219,0.417 1.219,0.417 1.219,0.729 false 0.438,0.323 0.896,0.521 0.458,0.198 10 false SST 3.042,0.271 3.323,0.521 0.281,0.25 10 false *a 0.146,1.406 0.427,1.656 0.281,0.25 10 false *b
*a Turn
*b Hold


Using SST, remove the inter shaft.

SST
09350-20015  (09369-20040)
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)


Hide 8.REMOVE FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR

a.
C237481
1.335,0.966 1.335,0.38 1.335,0.38 0.804,0.38 false 0.637,0.3 0.789,0.453 0.152,0.154 10 *1
*1 Protective Tape


Using a screwdriver, pry out the bearing retainer deflector.

HINT:

Tape the screwdriver tip before use.



Hide 10.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 12.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 13.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237691
2.557,0.612 2.557,0.318 2.557,0.318 2.66,0.318 false 2.69,0.232 2.992,0.388 0.302,0.156 10 SST

Using SST, remove the roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 14.REMOVE DIFFERENTIAL SIDE BEARING RETAINER

a.

Remove the 10 bolts and tap out the retainer with a plastic-faced hammer.


Hide 15.REMOVE DIFFERENTIAL CASE ASSEMBLY

Hide 16.REMOVE DIFFERENTIAL DRIVE PINION

Hide 17.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 18.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237482
0.689,1.031 0.689,1.793 false 1.061,1.552 1.061,1.676 1.061,1.676 0.689,1.676 false 0.527,1.805 0.834,1.954 0.307,0.149 10 SST

Using SST and a press, press out the roller bearing (inner) and drive pinion plate washer from the drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the drive pinion.


HINT:

If the drive pinion or ring gear is damaged, replace them as a set.



Hide 19.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237483

Using a brass bar and hammer, tap out the roller bearing (outer).


Hide 20.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C282337
2.281,1.365 2.5,1.365 2.5,1.365 2.5,1.521 false 2.26,1.521 2.698,1.521 false 1.156,0.146 1.469,0.344 0.313,0.198 10 false *a 2.76,0.865 3.073,1.063 0.313,0.198 10 false *b 2.771,1.417 3.083,1.615 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the roller bearing (outer).

SST
09502-12010  
09612-65014  (09612-01020, 09612-01050)


Hide 21.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap out the oil storage ring.


Hide 22.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
·

Measure the thickness of the case washer.

·

Tag the bearing outer races so that they can be reinstalled in the correct locations.



a.
C237485
0.948,0.552 0.427,0.552 true 0.792,1.042 0.552,1.042 0.552,1.042 0.552,0.563 true 0.094,0.469 0.396,0.625 0.302,0.156 10 false SST

Using SST and a press, press out the case bearing (outer) and plate washer from the bearing retainer.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

If the bearing is damaged during removal, replace it.



b.
C237486
1.229,0.49 0.542,0.49 true 1.104,0.927 0.76,0.927 0.76,0.927 0.76,0.5 true 0.198,0.406 0.5,0.563 0.302,0.156 10 false SST

Using SST and a press, press out the case bearing (outer) and plate washer from the differential carrier.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

If the bearing is damaged during removal, replace it.



Hide 23.REMOVE DIFFERENTIAL RING GEAR

a.
C236663
1.927,1.177 3.208,1.177 true 1.896,1.021 2.906,1.021 2.906,1.021 2.906,1.156 true 3.229,1.073 3.406,1.229 0.177,0.156 10 false *a
*a Matchmark


Place matchmarks on the ring gear and differential case.


b.

Remove the 10 ring gear set bolts.


c.
C236664

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 24.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:

The differential case and case bearings should only be removed when replacement is necessary.


a.
C282338
0.781,0.479 1.135,0.479 1.135,0.479 1.135,0.76 false 2.781,1.542 2.781,2.083 2.781,2.083 3.031,2.083 true 0.458,0.396 0.917,0.594 0.458,0.198 10 false SST 3.073,1.958 3.281,2.177 0.208,0.219 10 false *a 2.625,0.24 2.833,0.458 0.208,0.219 10 false *b 0.219,1.292 0.427,1.51 0.208,0.219 10 false *c
*a Notch
*b Turn
*c Hold


Using SST, remove the 2 case bearings (inner) from the differential case.

SST
09950-60010  (09951-00480)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09953-04020, 09958-04011)

HINT:

Attach the claws of SST to the notch in the differential case assembly to secure SST.



Hide 25. DISASSEMBLE DIFFERENTIAL CASE

a.
C236667

Using a chisel and hammer, unstake the differential case.


b.
C238726

Using a pin punch and hammer, tap out the straight pin.


c.
C236669

Remove the following parts from the differential case.

C236670
0.563,0.542 0.563,0.219 0.563,0.219 0.396,0.219 false 0.906,0.635 0.906,0.167 0.906,0.167 0.979,0.167 false 1.635,1.052 1.635,0.5 1.635,0.5 1.49,0.5 false 2.063,0.479 2.063,0.125 2.063,0.125 1.958,0.125 false 2.75,0.51 3,0.51 false 2.375,1.604 2.375,1.854 false 2.75,1.688 2.75,1.833 false 0.552,1.458 0.552,1.177 0.552,1.177 0.427,1.177 false 1.146,1.708 1.146,1.896 1.146,1.896 1.292,1.896 false 1.01,0.063 1.219,0.229 0.208,0.167 10 false (1) 0.156,0.115 0.365,0.281 0.208,0.167 10 false (2) 1.25,0.396 1.458,0.563 0.208,0.167 10 false (3) 1.708,0.042 1.917,0.208 0.208,0.167 10 false (4) 3.042,0.427 3.25,0.594 0.208,0.167 10 false (5) 2.271,1.865 2.479,2.031 0.208,0.167 10 false (1) 2.646,1.854 2.854,2.021 0.208,0.167 10 false (2) 1.333,1.802 1.542,1.969 0.208,0.167 10 false (4) 0.177,1.083 0.385,1.25 0.208,0.167 10 false (5)

(1) Differential pinion gear (2 pieces)

(2) Differential pinion gear thrust washer (2 pieces)

(3) Differential pinion shaft

(4) Differential side gear (2 pieces)

(5) Differential side gear thrust washer (2 pieces)



Hide 26.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.



Hide 27.INSPECT FRONT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.



Hide 28.REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

a.
C237523

Using a brass bar and hammer, tap out the 2 bearings.


Hide 29.REMOVE DIFFERENTIAL CLUTCH HUB

a.
C237524

Using a snap ring expander, remove the snap ring.


b.

Remove the differential clutch hub.


Hide 30.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH

a.
C237489
1.227,1.335 1.227,1.656 1.227,1.656 1.769,1.656 false 1.8,1.576 2.106,1.734 0.306,0.159 10 SST

Using SST, tap out the oil seal from the differential tube.

SST
09308-00010  


Hide 31.REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C237490

Using a snap ring expander, remove the snap ring.


b.

Remove the shaft from the differential tube.


Hide 32.REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING

a.

Using a snap ring expander, remove the snap ring.


b.
C237491
2.26,0.688 2.51,0.385 2.51,0.385 2.719,0.385 true 2.74,0.302 3.042,0.448 0.302,0.146 10 false SST

Using SST, a brass bar and a press, press out the shaft RH bearing.

SST
09950-00020  

NOTICE:
·

Do not damage the bearing.

·

Do not drop the shaft.




Hide 33.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB

a.
C237525

Check that there is no wear or damage on the clutch hub and clutch sleeve.

If necessary, replace them.



b.

Check that the clutch sleeve slides smoothly on the clutch hub.


Hide 34.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT

a.
C237646

Check that there is no wear or damage on the clutch sleeve and side gear inter shaft.

If necessary, replace clutch sleeve and side gear inter shaft.


b.

Check that clutch sleeve slides smoothly on the side gear inter shaft.


Hide 35.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE

a.
C237647

Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

Maximum clearance:

0.35 mm (0.0138 in.)


If the clearance is more than the maximum, replace the fork or clutch sleeve.