Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER OIL SEAL
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052561 FRONT DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.REMOVE NO. 2 ENGINE UNDER COVER

Hide 5.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

a.
C236628
1.287,0.537 1.287,0.208 1.287,0.208 1.945,0.208 false 1.988,0.131 2.301,0.297 0.313,0.167 10 SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C236629
2.229,1.208 2.656,1.208 false 2.708,1.125 3.031,1.292 0.323,0.167 10 false SST 0.51,0.365 0.677,0.521 0.167,0.156 10 false *a 2.188,1.74 2.354,1.896 0.167,0.156 10 false *b
*a Turn
*b Hold


Using SST to hold the companion flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 6.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C236630
1.876,1.853 2.192,2.006 0.316,0.153 10 SST 2.03,1.465 2.03,1.846 false

Using SST, remove the companion flange with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 7.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
C236631
2.719,1.479 2.719,1.75 false 1.427,0.76 1.563,0.26 1.563,0.26 1.75,0.26 false 1.219,1.438 1.219,1.823 false 2.583,1.781 2.885,1.948 0.302,0.167 10 false SST 1.792,0.156 1.948,0.323 0.156,0.167 10 false *1 1.146,1.844 1.302,2.01 0.156,0.167 10 false *2
*1 Oil Seal
*2 Oil Slinger


Using SST, remove the oil seal.

SST
09308-10010  


Hide 8.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Remove the oil slinger from the drive pinion.


Hide 9.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237691
2.557,0.612 2.557,0.318 2.557,0.318 2.66,0.318 false 2.69,0.232 2.992,0.388 0.302,0.156 10 SST

Using SST, remove the roller bearing (inner).

SST
09556-22010  


b.
C236633
1.883,0.706 1.883,0.237 1.883,0.237 2.318,0.237 false 2.347,0.154 2.656,0.3 0.309,0.147 10 SST

Using SST, tap out the roller bearing (outer).

SST
09308-00010  


Hide 10.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a screwdriver and hammer, tap out the oil storage ring.


Hide 11.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237692

Remove the bearing spacer from the drive pinion.


Hide 12.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237692

Install a new bearing spacer.

HINT:

Make sure the spacer is installed correctly.



Hide 13.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap in a new oil storage ring.

NOTICE:

Be careful not to damage the oil storage ring.



Hide 14.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C283888
0.854,1.875 1.438,2.01 1.438,2.01 1.302,1.875 false 1.479,1.948 1.938,2.146 0.458,0.198 10 false SST

Using SST and a hammer, install the roller bearing (outer).

SST
09316-60011  (09316-00011)


b.

Install the roller bearing (inner).


Hide 15.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Install the oil slinger to the drive pinion.


Hide 16.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.


b.
C236636
2.417,1.406 2.417,1.771 false 2.281,1.813 2.594,1.969 0.313,0.156 10 false SST 1.333,0.031 1.51,0.188 0.177,0.156 10 false *a
*a Oil Seal Depth


Using SST and a hammer, tap in the oil seal.

SST
09554-22010  

Oil seal depth:

4.35 +/-0.45 mm (0.171 +/-0.0177 in.)



Hide 17.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C236637
2.073,1.469 2.073,1.802 false 1.938,1.844 2.24,2 0.302,0.156 10 false SST

Using SST, install the companion flange with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to drive pinion thread and nut seat face.


c.
C282254
0.573,0.594 0.896,0.594 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.281,0.51 0.594,0.708 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange, install a new nut.

SST
09330-00021  (09330-00030)

Torque:
370 N*m (3773 kgf*cm, 27 ft.*lbf)

or less



Hide 18.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C236639

Using a torque wrench, measure the preload.

Preload (Starting Torque):
Item Specified Condition
New bearing 1.0 to 1.5 N*m (10 to 16 kgf*cm, 9 to 13 in.*lbf)
Reused bearing 0.5 to 0.7 N*m (6 to 7 kgf*cm, 5 to 6 in.*lbf)


If the result is not as specified, adjust the preload (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT DIFFERENTIAL CARRIER ASSEMBLY>REASSEMBLY).



Hide 19.INSPECT TOTAL PRELOAD

a.

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (starting torque):

0.3 to 0.8 N*m (4 to 8 kgf*cm, 3 to 7 in.*lbf) + drive pinion preload


If necessary, disassemble and inspect the differential.


Hide 20.STAKE FRONT DRIVE PINION COMPANION FLANGE NUT

a.
C236640

Using a chisel and hammer, stake the nut.