Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052564 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 2.REMOVE REAR DRIVE PINION NUT

a.
C236628
1.287,0.537 1.287,0.208 1.287,0.208 1.945,0.208 false 1.988,0.131 2.301,0.297 0.313,0.167 10 SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C236629
2.229,1.208 2.656,1.208 false 2.708,1.125 3.031,1.292 0.323,0.167 10 false SST 0.51,0.365 0.677,0.521 0.167,0.156 10 false *a 2.188,1.74 2.354,1.896 0.167,0.156 10 false *b
*a Turn
*b Hold


Using SST to hold the companion flange in place, remove the nut.

SST
09330-00021  (09330-00030)


Hide 3.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C238724

Using SST, remove the companion flange with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 4.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C236631
2.719,1.479 2.719,1.75 false 1.427,0.76 1.563,0.26 1.563,0.26 1.75,0.26 false 1.219,1.438 1.219,1.823 false 2.583,1.781 2.885,1.948 0.302,0.167 10 false SST 1.792,0.156 1.948,0.323 0.156,0.167 10 false *1 1.146,1.844 1.302,2.01 0.156,0.167 10 false *2
*1 Oil Seal
*2 Oil Slinger


Using SST, remove the oil seal.

SST
09308-10010  


Hide 5.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Remove the oil slinger from the drive pinion.


Hide 6.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C236632
2.759,0.251 3.073,0.412 0.314,0.161 10 SST 2.384,0.756 2.384,0.325 2.384,0.325 2.725,0.325 false

Using SST, remove the roller bearing (inner).

SST
09556-22010  


b.
C236633
1.883,0.706 1.883,0.237 1.883,0.237 2.318,0.237 false 2.347,0.154 2.656,0.3 0.309,0.147 10 SST

Using SST, tap out the roller bearing (outer).

SST
09308-00010  


Hide 7.REMOVE DIFFERENTIAL OIL STORAGE RING

a.

Using a screwdriver and hammer, tap out the oil storage ring.


Hide 8.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237515

Remove the bearing spacer from the drive pinion.


Hide 9.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237515

Install a new bearing spacer.

HINT:

Make sure the spacer is installed correctly.



Hide 10.INSTALL DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap in a new oil storage ring.

NOTICE:

Be careful not to damage the oil storage ring.



Hide 11.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237516
1.448,1.875 1.448,2 1.448,2 1.792,2 false 0.875,1.938 1.448,1.938 true 1.823,1.917 2.135,2.073 0.313,0.156 10 false SST

Using SST and a hammer, tap in the roller bearing (outer).

SST
09316-60011  (09316-00011, 09316-00021)


b.

Install the roller bearing (inner).


Hide 12.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Install the oil slinger to the drive pinion.


Hide 13.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C236636
2.417,1.406 2.417,1.771 false 2.281,1.813 2.594,1.969 0.313,0.156 10 false SST 1.333,0.031 1.51,0.188 0.177,0.156 10 false *a
*a Oil Seal Depth


Using SST and a hammer, tap in a new oil seal.

SST
09554-30011  

Standard oil seal depth:

0 +/-0.3mm (0 +/-0.0118in.)



b.

Apply MP grease to the lip of the oil seal.


Hide 14.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C238725

Using SST, install the companion flange with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to drive pinion thread and nut seat face.


c.
C282254
0.573,0.594 0.896,0.594 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.281,0.51 0.594,0.708 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange in place, install a new nut.

SST
09330-00021  (09330-00030)

Torque:
370 N*m (3773 kgf*cm, 273 ft.*lbf)

or less



Hide 15.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C236639

Using a torque wrench, measure the preload.

Standard Preload (Starting Torque):
Item Specified Condition
New bearing 1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf)
Reused bearing 0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf)


If the result is not as specified, adjust the preload.



Hide 16.INSPECT TOTAL PRELOAD

a.
C236639

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload:
Bearing Specified Condition
New 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
Reused 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload


If the result is not as specified, adjust the preload.


Hide 17.STAKE DRIVE PINION NUT

a.
C236640

Using a chisel and hammer, stake the nut.