Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052565 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C236647

Secure the differential carrier.


Hide 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C236648
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C236649

Using a dial indicator, check the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

C236650

a.

Using a dial indicator, check the backlash of the ring gear.

Backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C236632
2.759,0.251 3.073,0.412 0.314,0.161 10 SST 2.384,0.756 2.384,0.325 2.384,0.325 2.725,0.325 false

Using SST, remove the roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 12.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C236656

Remove the 2 bolts and 2 adjusting nut locks.


Hide 13.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C236657
1.677,1.292 0.333,1.292 true 1.667,1.229 1.021,1.229 1.021,1.229 1.021,1.292 true 1.24,0.917 0.844,0.917 0.844,0.917 0.844,1.281 true 1.24,0.865 0.656,0.865 0.656,0.865 0.656,1.281 true 0.156,1.198 0.365,1.438 0.208,0.24 10 false *a
*a Matchmark


Place matchmarks on the bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 adjusting nuts.


d.
C236658

Remove the rear differential case assembly from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



Hide 14.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the drive pinion and bearing spacer from the differential carrier.


Hide 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237656
2.731,0.394 3.04,0.551 0.309,0.157 10 SST 2.334,1.03 2.605,0.467 2.605,0.467 2.697,0.467 false

Using SST and a press, press out the roller bearing (inner) and drive pinion plate washer from the drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the drive pinion.


HINT:

If the drive pinion or ring gear is damaged, replace them as a set.



Hide 16.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237657
1.323,0.141 1.635,0.304 0.313,0.163 10 SST 1.056,0.223 1.297,0.223 false

Using SST, remove the roller bearing (outer) from the carrier.

SST
09308-00010  


b.

Using a brass bar and hammer, tap out the oil storage ring from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 18.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C236662

Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 19.REMOVE DIFFERENTIAL RING GEAR

a.
C236663
1.927,1.177 3.208,1.177 true 1.896,1.021 2.906,1.021 2.906,1.021 2.906,1.156 true 3.229,1.073 3.406,1.229 0.177,0.156 10 false *a
*a Matchmark


Place matchmarks on the ring gear and differential case.


b.

Using a screwdriver and hammer, pry out the lock plates.


c.

Remove the 10 ring gear set bolts and 5 lock plates.


d.
C236664

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 20.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.

a.

Install the rear differential case bearings (outer) to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 adjusting nuts.


d.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
85 N*m (870 kgf*cm, 63 ft.*lbf)


e.
C236665

Using a dial indicator, measure the differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



f.

Remove the 4 bolts and 2 bearing caps.


g.

Remove the 2 adjusting nuts.


h.

Remove the differential case.


i.

Remove the rear differential case bearings (outer).


Hide 21.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C236666
1.052,0.751 1.052,0.373 1.052,0.373 0.71,0.373 false 0.36,0.293 0.668,0.456 0.308,0.162 10 SST

Using SST, remove the 2 bearings from the differential case.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

HINT:

Do not remove the case bearings when not replacing the differential case.



Hide 22.DISASSEMBLE DIFFERENTIAL CASE (for 2 Pinion Gear Type)

a.
C236667

Using a chisel and hammer, unstake the differential case.


b.
C238726

Using a pin punch and hammer, tap out the straight pin.


c.
C236669

Remove the following parts from the differential case.

C236670
0.563,0.542 0.563,0.25 0.563,0.25 0.396,0.25 false 0.906,0.625 0.906,0.198 0.906,0.198 0.979,0.198 false 1.635,1.042 1.635,0.521 1.635,0.521 1.49,0.521 false 2.063,0.479 2.063,0.156 2.063,0.156 1.958,0.156 false 2.74,0.51 2.969,0.51 false 2.375,1.625 2.375,1.875 false 2.75,1.698 2.75,1.844 false 0.552,1.469 0.552,1.208 0.552,1.208 0.427,1.208 false 1.135,1.729 1.135,1.917 1.135,1.917 1.281,1.917 false 1.01,0.094 1.219,0.26 0.208,0.167 10 false (1) 0.156,0.146 0.365,0.313 0.208,0.167 10 false (2) 1.281,0.417 1.49,0.583 0.208,0.167 10 false (3) 1.719,0.063 1.927,0.229 0.208,0.167 10 false (4) 3.01,0.406 3.219,0.573 0.208,0.167 10 false (5) 2.292,1.885 2.5,2.052 0.208,0.167 10 false (1) 2.677,1.865 2.885,2.031 0.208,0.167 10 false (2) 1.333,1.823 1.542,1.99 0.208,0.167 10 false (4) 0.208,1.104 0.417,1.271 0.208,0.167 10 false (5)

(1) Side gear (2 pieces)

(2) Side gear thrust washer (2 pieces)

(3) Pinion shaft

(4) Pinion gear (2 pieces)

(5) Pinion gear thrust washer (2 pieces)



d.

Using a chisel and hammer, unstake the differential case.


Hide 23.DISASSEMBLE DIFFERENTIAL CASE (for LSD)

a.
C237349
1.052,1.573 2.906,1.573 true 1.052,1.438 1.708,1.438 1.708,1.438 1.708,1.552 true 2.927,1.49 3.115,1.667 0.188,0.177 10 false *a
*a Matchmark


Place matchmarks on the LH and RH cases.


b.

Remove the 8 bolts.

NOTICE:

Diametrically loosen and remove the bolts in several passes.



c.
C237659
0.948,0.188 0.646,0.188 false 1.938,1.875 0.615,1.875 false 0.885,1.281 0.885,1.875 false 1.469,1.635 1.469,1.865 false 0.438,1.042 0.438,1.271 false 2.99,1.396 3.177,1.396 false 2.469,1.896 2.698,1.896 false 1.656,0.458 1.656,0.271 1.656,0.271 3.01,0.271 false 2.656,1.042 2.656,0.271 false 2.167,0.74 2.167,0.271 false 0.417,0.073 0.625,0.26 0.208,0.188 10 false (1) 0.396,1.75 0.604,1.938 0.208,0.188 10 false (2) 0.354,1.313 0.563,1.5 0.208,0.188 10 false (4) 3.208,1.281 3.417,1.469 0.208,0.188 10 false (4) 2.74,1.792 2.948,1.979 0.208,0.188 10 false (1) 3.042,0.146 3.25,0.333 0.208,0.188 10 false (3)

Remove the following parts from the differential cases.

(1) Side gear (2 pieces)

(2) No. 1 Side gear thrust washer (6 pieces)

(3) Clutch plate (6 pieces)

(4) Side gear thrust washer (2 pieces)

C237660
1.01,0.583 1.01,0.385 1.01,0.385 0.552,0.385 false 2.198,1.292 2.563,1.292 false 1.823,1.583 2.25,1.583 false 1.021,1.146 1.021,0.958 1.021,0.958 0.583,0.958 false 1.313,0.771 1.313,0.135 1.313,0.135 0.854,0.135 false 1.698,0.25 1.698,0.125 1.698,0.125 1.896,0.125 false 2.333,0.781 2.333,0.26 2.333,0.26 2.51,0.26 false 1.802,0.531 2.333,0.531 false 2.688,0.802 2.979,0.802 false 1.573,1.813 0.49,1.813 false 0.813,1.438 0.813,1.813 false 1.604,1.208 1.417,1.594 1.417,1.594 1.313,1.594 false 0.365,0.26 0.573,0.448 0.208,0.188 10 false (5) 2.594,1.177 2.802,1.365 0.208,0.188 10 false (6) 2.281,1.458 2.49,1.646 0.208,0.188 10 false (8) 0.396,0.833 0.604,1.021 0.208,0.188 10 false (8) 0.667,0.021 0.875,0.208 0.208,0.188 10 false (7) 2.542,0.135 2.75,0.323 0.208,0.188 10 false (8) 1.938,0.021 2.146,0.208 0.208,0.188 10 false (9) 3,0.677 3.208,0.865 0.208,0.188 10 false (9) 0.302,1.688 0.51,1.875 0.208,0.188 10 false (9) 1.042,1.479 1.323,1.667 0.281,0.188 10 false (10)

(5) Spring retainer RH

(6) Spring retainer LH

(7) Compression spring

(8) Pinion gear (4 pieces)

(9) Pinion gear thrust washer (4 pieces)

(10) Spider



Hide 24.INSPECT REAR NO. 1 DIFFERENTIAL SIDE GEAR THRUST WASHER (for LSD)

a.
C237661

Using a micrometer, measure the thickness of the thrust washer. Also, check that there is no bare metal.

Standard thickness:

1.77 to 1.86 mm (0.0697 to 0.0732 in.)


If necessary, replace the thrust washers.

HINT:

If replacing the thrust washer, also replace the clutch plate that it contacts.




Hide 25.INSPECT CLUTCH PLATE (for LSD)

a.
C237662

Using a micrometer, measure the thickness of the clutch plate. Also, check that there is no abnormal wear.

Standard thickness:

1.57 to 1.63 mm (0.0619 to 0.0641 in.)


If necessary, replace the clutch plate.



Hide 26.INSPECT COMPRESSION SPRING (for LSD)

a.
C237663

Using a vernier caliper, measure the free length of the spring.

Minimum free length:

27.02 mm (1.063 in.)


If the length is less than the minimum, replace the spring.



Hide 27.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.



Hide 28.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.