Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made)
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052568 REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL DIFFERENTIAL RING GEAR

C282511
0.958,0.198 1.198,0.198 1.198,0.198 1.354,0.927 false 0.708,0.104 1.073,0.302 0.365,0.198 10 false *a
*a Boiling Water


a.

Clean the contact surfaces of the differential case and ring gear.


b.

Heat the ring gear in boiling water that is approximately 100°C (212°F).


c.

Carefully remove the ring gear from the boiling water.


d.

After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.


e.
C282512
1.375,1.688 0.917,1.625 0.917,1.625 1.417,1.563 true 0.677,1.521 0.958,1.688 0.281,0.167 10 false *a
*a Matchmark


Align the matchmarks on the ring gear with those of the differential case.


f.

Temporarily install the 10 bolts.


g.

After the ring gear cools down, uniformly tighten the 10 bolts in diametrically opposite pairs in several passes.

T = 160 to 180 N*m{ 1,632 to 1835 kgf*cm 118 to 133 ft.*lbf }


Hide 2.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C123201
1.417,1.958 0.635,1.76 false 1.531,0.385 0.854,0.385 0.854,0.385 1.385,0.583 false 0.302,1.667 0.615,1.813 0.313,0.146 10 false SST 0.51,0.313 0.823,0.458 0.313,0.146 10 false SST

Using SST and a press, press the bearing onto the differential case.

SST
09950-60010  (09951-00430, 09951-00480, 09951-00470, 09951-00550)
09950-70010  (09951-07150, 09951-00560, 09951-00570)


Hide 3.INSPECT DIFFERENTIAL RING GEAR RUNOUT

a.

Install the differential case on the carrier, and install the 2 side shims so that there is no play in the bearing.


b.

Install the 2 bearing caps with the 4 bolts.

Torque:
85 N*m (870 kgf*cm, 63 ft.*lbf)


c.
C121134

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.07 mm (0.0028 in.)



d.

Remove the 2 bearing caps, 2 side shims and differential case.


Hide 4.INSTALL REAR DIFFERENTIAL DUST DEFLECTOR

a.
C121141
2.76,1.792 2.052,1.792 false 2.479,0.542 2.177,0.542 false 2.177,0.542 2.177,1.073 false 2.813,1.719 3.125,1.875 0.313,0.156 10 false SST 2.51,0.469 2.875,0.625 0.365,0.156 10 false *1
*1 Plate


Using SST, a plate and a press, press in the dust deflector.

SST
09636-20010  

NOTICE:

Be careful not to damage the dust deflector.



Hide 5.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C197664
1.948,0.563 2.26,0.563 2.26,0.563 1.969,0.938 true 2.344,0.5 2.708,0.677 0.365,0.177 10 false SST

Using SST and a press, press the roller bearing (outer) to the carrier.

SST
09316-60011  (09316-00011, 09316-00021)


Hide 6.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
F044252
1.688,0.781 2.125,0.542 2.125,0.542 1.625,1.188 false 2.167,0.438 2.479,0.583 0.313,0.146 10 false SST

Using SST and a press, press the roller bearing (outer) into the carrier.

SST
09316-60011  (09316-00041, 09316-00011)


Hide 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.

Install the plate washer on the drive pinion.

HINT:

First fit a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.



b.
SA03102
1.885,1.344 2.281,0.99 2.281,0.99 2.625,0.99 false 2.698,0.875 3.146,1.063 0.448,0.188 10 false SST

Using SST and a press, press the roller bearing (inner) onto the drive pinion.

SST
09506-30012  


Hide 8.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C093601

Install a new bearing spacer to the drive pinion.


b.
C028218

Install the rear drive pinion front tapered roller bearing.


c.

Install the rear differential drive pinion oil slinger.


d.

Apply MP grease to a new oil seal.


e.
R011163

Using SST, install the companion flange on the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



f.
C283422
0.833,0.74 0.76,0.438 0.76,0.438 0.552,0.438 false 0.208,0.344 0.667,0.542 0.458,0.198 10 false SST

Using SST to hold the companion flange in place, torque the nut.

SST
09330-00021  (09330-00030)


g.
SA02352

Using a torque wrench, measure the preload.

Standard preload (at start of torque):
Bearing Preload
New bearing 1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf)
Reused bearing 0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 4.9 to 7.5 in.*lbf)


If the preload is greater than the maximum, replace the bearing spacer.

If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.


T = 678 N*m{ 6,914 kgf*cm 500 ft.*lbf }

If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.

HINT:

Do not loosen the pinion nut to reduce the preload.




Hide 9.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C028220

Place the 2 bearing outer races on their respective bearings and 2 side shims.

HINT:

Make sure the right and left races are not interchanged.



b.
C121142

Align matchmarks on the bearing cap and differential carrier, and install the 2 bearing caps.

NOTICE:

Make sure the right and left bearing caps are not interchanged.



c.

Tighten both bearing caps with the 4 bolts.

Torque:
85 N*m (870 kgf*cm, 63 ft.*lbf)


Hide 10.INSPECT BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

SST
09504-00011  
09960-10010  (09962-01000, 09963-00700)

C121135

a.

Set the dial indicator perpendicular to the end of the ring gear face.


b.

While holding the rear drive pinion companion flange, rotate the ring gear and measure the backlash.

Standard backlash:

0.13 to 0.20 mm (0.0051 to 0.0078 in.)



Hide 11.ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C121144

Select a side shim so that the ring gear backlash is within the specification. Then, install it to the ring gear back side.

HINT:
·

If the case bearing is new, select a thinner side shim and install it.

·

If the case bearing is reused, install a side shim with the same thickness as the removed one.

Standard side shim thickness:
Thickness Thickness Thickness
2.51 mm (0.099 in.) 3.12 mm (0.123 in.) 3.73 mm (0.147 in.)
2.54 mm (0.100 in.) 3.15 mm (0.124 in.) 3.76 mm (0.148 in.)
2.57 mm (0.101 in.) 3.18 mm (0.125 in.) 3.78 mm (0.149 in.)
2.59 mm (0.102 in.) 3.20 mm (0.126 in.) 3.81 mm (0.150 in.)
2.62 mm (0.103 in.) 3.23 mm (0.127 in.) 3.84 mm (0.151 in.)
2.64 mm (0.104 in.) 3.25 mm (0.128 in.) 3.86 mm (0.152 in.)
2.67 mm (0.105 in.) 3.28 mm (0.129 in.) 3.89 mm (0.153 in.)
2.69 mm (0.106 in.) 3.30 mm (0.130 in.) 3.91 mm (0.154 in.)
2.72 mm (0.107 in.) 3.33 mm (0.131 in.) 3.94 mm (0.155 in.)
2.74 mm (0.108 in.) 3.35 mm (0.132 in.) 3.96 mm (0.156 in.)
2.77 mm (0.109 in.) 3.38 mm (0.133 in.) 3.99 mm (0.157 in.)
2.79 mm (0.110 in.) 3.40 mm (0.134 in.) 4.01 mm (0.158 in.)
2.82 mm (0.111 in.) 3.43 mm (0.135 in.) 4.04 mm (0.159 in.)
2.84 mm (0.112 in.) 3.45 mm (0.136 in.) 4.06 mm (0.160 in.)
2.87 mm (0.113 in.) 3.48 mm (0.137 in.) 4.09 mm (0.161 in.)
2.90 mm (0.114 in.) 3.51 mm (0.138 in.) 4.11 mm (0.162 in.)
2.92 mm (0.115 in.) 3.53 mm (0.139 in.) 4.14 mm (0.163 in.)
2.95 mm (0.116 in.) 3.56 mm (0.140 in.) 4.17 mm (0.164 in.)
2.97 mm (0.117 in.) 3.58 mm (0.141 in.) 4.19 mm (0.165 in.)
3.00 mm (0.118 in.) 3.61 mm (0.142 in.) 4.22 mm (0.166 in.)
3.02 mm (0.119 in.) 3.63 mm (0.143 in.) 4.24 mm (0.167 in.)
3.05 mm (0.120 in.) 3.66 mm (0.144 in.) 4.27 mm (0.168 in.)
3.07 mm (0.121 in.) 3.68 mm (0.145 in.) 4.29 mm (0.169 in.)
3.10 mm (0.122 in.) 3.71 mm (0.146 in.) -





b.

Make the differential case bearing and side shim snug by tapping on the ring gear with a plastic-faced hammer.


c.
C121135

Set the dial indicator perpendicular to the end of the ring gear face.


d.

While holding the rear drive pinion companion flange, rotate the ring gear and measure the backlash.

Standard backlash:

0.13 to 0.20 mm (0.0051 to 0.0078 in.)



e.
C121144

If the backlash is not within the specification, select a side shim so that the ring gear backlash is within the specification. Then, install it to the ring gear back side.


f.
C121147
3,1.031 3,1.521 true 2.26,0.854 2.26,1.833 true 2.938,1.563 3.25,1.781 0.313,0.219 10 false *2 2.198,1.854 2.469,2.031 0.271,0.177 10 false *1
*1 Plate Washer
*2 Case Bearing


Select a thicker side shim so that the clearance between the case bearing outer race end on the ring gear teeth side and the carrier becomes 0 or around 0.


g.

Make the differential case bearing and side shim snug by tapping on the ring gear with a plastic-faced hammer.


h.
C121148

Select the dial indicator perpendicular to the end of the ring gear face.


i.

While holding the rear drive pinion companion flange rear, rotate the ring gear and measure the backlash.

Standard backlash:

0.13 to 0.20 mm (0.0051 to 0.0078 in.)


If the backlash is not within the specification, adjust the thickness of the right and left side shim by an equal amount so that the backlash is within the specification.



Hide 12.INSPECT TOTAL PRELOAD

a.
C003092

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

HINT:

A bolt without a torque specification is shown in the service data (See page General>SPECIFICATIONS>AXLE AND DIFFERENTIAL>SERVICE DATA).


If necessary, disassemble and inspect the differential.



Hide 13.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C014071

Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead primer.


b.

Hold the companion flange firmly in place and rotate the ring gear in both directions.


c.

Inspect the tooth contact pattern.

C113184
1.156,1.073 2.167,1.26 1.01,0.188 10 false Proper Contact 2.396,0.146 3.094,0.313 0.698,0.167 10 false Drive Side 3.667,0.167 4.458,0.354 0.792,0.188 10 false Toe Contact 5.51,0.177 6.375,0.344 0.865,0.167 10 false Face Contact 3.458,1.667 6.167,2.031 2.708,0.365 10 false Select an adjusting washer that will shift the drive pinion closer to the ring gear. 3.573,2.552 4.427,2.719 0.854,0.167 10 false Heel Contact 5.396,2.531 6.333,2.708 0.938,0.177 10 false Flank Contact 3.552,3.99 6.333,4.375 2.781,0.385 10 false Select an adjusting washer that will shift the drive pinion away from the ring gear. 2.375,4.979 3.083,5.167 0.708,0.188 10 false Coast Side 3.563,5.021 4.417,5.188 0.854,0.167 10 false Heel Contact 5.385,5 6.323,5.177 0.938,0.177 10 false Flank Contact 3.594,7.417 4.385,7.604 0.792,0.188 10 false Toe Contact 5.438,7.438 6.302,7.604 0.865,0.167 10 false Face Contact 3.385,6.521 6.083,6.885 2.698,0.365 10 false Select an adjusting washer that will shift the drive pinion closer to the ring gear. 3.552,8.833 6.292,9.188 2.74,0.354 10 false Select an adjusting washer that will shift the drive pinion away from the ring gear.

C282513
1.719,1.833 1.719,1.49 false 1.646,1.865 1.938,2.052 0.292,0.188 10 false *1
*1 Plate Washer


If the teeth are not contacting properly, use the following chart to select a proper washer.

Standard plate washer thickness:
Thickness mm (in.) Thickness mm (in.)
0.69 mm (0.0272 in.) 1.19 mm (0.0469 in.)
0.71 mm (0.0280 in.) 1.22 mm (0.0480 in.)
0.74 mm (0.0291 in.) 1.24 mm (0.0488 in.)
0.76 mm (0.0300 in.) 1.27 mm (0.0500 in.)
0.79 mm (0.0311 in.) 1.30 mm (0.0512 in.)
0.81 mm (0.0319 in.) 1.32 mm (0.0520 in.)
0.84 mm (0.0331 in.) 1.35 mm (0.0531 in.)
0.86 mm (0.0339 in.) 1.37 mm (0.0540 in.)
0.89 mm (0.0350 in.) 1.40 mm (0.0551 in.)
0.91 mm (0.0358 in.) 1.42 mm (0.0559 in.)
0.94 mm (0.0370 in.) 1.45 mm (0.0571 in.)
0.97 mm (0.0382 in.) 1.47 mm (0.0579 in.)
0.99 mm (0.0390 in.) 1.50 mm (0.0591 in.)
1.02 mm (0.0402 in.) 1.52 mm (0.0598 in.)
1.04 mm (0.0409 in.) 1.55 mm (0.0610 in.)
1.07 mm (0.0421 in.) 1.58 mm (0.0622 in.)
1.09 mm (0.0429 in.) 1.60 mm (0.0630 in.)
1.12 mm (0.0441 in.) 1.63 mm (0.0642 in.)
1.14 mm (0.0449 in.) 1.65 mm (0.0650 in.)
1.17 mm (0.0461 in.) -




Hide 15.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 16.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 18.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C093601

Install a new bearing spacer to the drive pinion.


Hide 19.INSTALL DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap in a new oil storage ring.

NOTICE:

Be careful not to damage the oil storage ring.



Hide 20.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C028218

Hide 21.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 22.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.


b.

Using a brass bar and hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

NOTICE:

Do not damage the oil seal.



Hide 23.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C283421
1.458,0.646 1.292,0.51 1.292,0.51 0.979,0.51 false 2.125,1.417 2.302,1.74 2.302,1.74 2.5,1.74 false 0.615,0.396 1.073,0.594 0.458,0.198 10 false SST 2.542,1.625 3,1.823 0.458,0.198 10 false SST

Using SST, install the companion flange on the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.
C283422
0.833,0.74 0.76,0.438 0.76,0.438 0.552,0.438 false 0.208,0.344 0.667,0.542 0.458,0.198 10 false SST

Using SST to hold the flange, torque the nut.

SST
09330-00021  (09330-00030)

T = 370 N*m{ 3,770 kgf*cm 273 ft.*lbf } or less


Hide 24.INSPECT DRIVE PINION PRELOAD

a.
SA02352

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard preload (at start of torque):
Bearing Preload
New bearing 1.20 to 2.00 N*m (12 to 20 kgf*cm, 11 to 18 in.*lbf)
Reused bearing 0.70 to 1.50 N*m (7 to 15 kgf*cm, 6.0 to 13 in.*lbf)


If the preload is greater than the maximum, replace the bearing spacer.


If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.


T = 678 N*m{ 6,914 kgf*cm 500 ft.*lbf } or less

If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.


HINT:

Do not loosen the pinion nut to reduce the preload.



Hide 25.INSPECT TOTAL PRELOAD

a.
SA02352

Using a torque wrench, measure the preload.

HINT:

A bolt without a torque specification is shown in the service data (See page General>SPECIFICATIONS>AXLE AND DIFFERENTIAL>SERVICE DATA).


If necessary, disassemble and inspect the differential.



Hide 26.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C121135

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.13 to 0.20 mm (0.0051 to 0.0078 in.)


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

HINT:

Perform the measurements at 3 or more positions around the circumference of the ring gear.




Hide 27.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
F001237
1.313,1.927 2.375,2.115 1.063,0.188 10 true 30 mm (1.18 in.)

Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.

Maximum runout:
Runout Maximum
Vertical runout 0.10 mm (0.0039 in.)
Lateral runout 0.10 mm (0.0039 in.)


If the runout is greater than the maximum, replace the companion flange.



Hide 28.STAKE DRIVE PINION NUT

a.
ZK07449

Using a chisel and hammer, stake the nut.