Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER(for 4WD and Pre-Runner) › 2012.04–2012.10
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052578 FRONT SHOCK ABSORBER(for 4WD and Pre-Runner) A

FRONT SUSPENSION  FRONT SHOCK ABSORBER(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT COIL SPRING LH

a.
C159782N03
0.115,0.613 0.414,0.758 0.3,0.145 10 SST 0.464,0.688 0.688,0.688 false 0.688,0.688 0.727,0.793 false

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00031)
09727-00060  


b.
C275706C13
0.208,0.135 0.521,0.292 0.313,0.156 10 false *a 0.271,2.542 0.583,2.698 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Attach the arm of SST to the diameter of the coil spring.

CAUTION:
·

Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




d.
C281866C01
2.229,1.948 2.51,1.688 2.51,1.688 2.667,1.688 false 2.896,0.677 3.208,0.833 0.313,0.156 10 false *a 2.74,1.615 3.198,1.813 0.458,0.198 10 false SST
*a Recess


Install the coil spring to the shock absorber. Fit the lower end of the coil spring into the recess of the spring lower seat.


Hide 2.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Install the cushion retainer to the shock absorber.


b.

Install the suspension support to the shock absorber.


Hide 3.INSTALL FRONT SHOCK ABSORBER CUSHION

a.

Install the cushion to the shock absorber.


Hide 4.INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER

a.

Install the cushion retainer to the shock absorber.


Hide 5.INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C113160C01
0.938,1.438 0.938,1.771 false 2.469,1.448 2.469,1.792 false 1.635,0.146 1.875,0.313 0.24,0.167 10 false *b 2.76,0.135 3.01,0.333 0.25,0.198 10 false *c 0.844,1.802 1.135,1.99 0.292,0.188 10 false *1 2.396,1.813 2.646,1.979 0.25,0.167 10 false *2 0.385,0.177 0.615,0.385 0.229,0.208 10 false *a
*1 Suspension Support
*2 Absorber Bush
*a for LH
*b Front
*c for RH


Align the suspension support and absorber bush as shown in the illustration.


b.

Install a new lock nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.



c.

Release the coil spring while checking the position of the spring lower seat and suspension support.


Hide 6.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

C113161

a.

Install the shock absorber to the body so that the lower end of the coil spring faces the rear of the vehicle.


b.
C288512C01
0.542,3.615 0.865,3.615 0.865,3.615 1.01,4.01 false 0.792,0.229 1.083,0.229 1.083,0.229 1.448,0.698 true 2.073,2.448 2.385,2.604 0.313,0.156 10 false *a 0.229,3.531 0.688,3.729 0.458,0.198 10 false SST 0.469,0.135 0.927,0.333 0.458,0.198 10 true SST
*a Fulcrum Length


Using SST, install the 3 nuts to the upper side of the front shock absorber with coil spring.

SST
09249-B1010  

Torque:
without SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)
with SST : 28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).



c.
F049985

Temporarily install the bolt and nut as shown in the illustration.

HINT:

Fix the nut in place and temporarily install the bolt.



Hide 9.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the stabilizer link to the steering knuckle with the nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 10.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 11.INSTALL FRONT WHEEL

a.

Install the front wheel.

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)


Hide 12.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Press down on the vehicle several times to stabilize the suspension.


Hide 13.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 14.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT