Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner) › 2012.04–2012.10
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052579 FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SPRING BUMPER

a.

Install the front spring bumper to the vehicle.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 2.INSTALL LOWER BALL JOINT ASSEMBLY

a.
C237856
1.594,0.177 2.115,0.177 2.115,0.177 2.625,0.844 true 2.448,2.323 2.75,2.323 false 2.75,2.323 2.906,1.938 false 1.208,0.115 1.615,0.323 0.406,0.208 10 false SST 2.031,2.24 2.438,2.448 0.406,0.208 10 false SST

Using SST and press, press in a new lower ball joint.

SST
09226-10010  
09631-32020  


b.

Install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



c.
C237891C01
1.615,0.75 1.76,0.75 false 2.115,0.75 2.25,0.75 false 1.646,0.771 1.76,0.771 false 2.115,0.771 2.229,0.771 false 0.844,0.583 1.677,0.583 false 1.677,0.583 1.677,0.74 false 1.156,0.594 1.156,1.115 1.156,1.115 1.583,1.115 true 0.656,0.5 0.885,0.688 0.229,0.188 10 false *1
*1 MP Grease No. 2


Pack the upper ball joint with MP grease No. 2.

Grease capacity:

8.0 g (0.282 oz.)



d.

Apply MP grease to the locations shown in the illustration.

NOTICE:

Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.



e.

Install a new dust cover to the lower arm.


f.

Install a new dust cover set ring.


Hide 3.INSTALL FRONT NO. 2 LOWER ARM BUSH

a.
C281962C01
0.385,3.646 0.917,3.26 0.917,3.26 0.406,4.115 true 0.604,0.76 0.531,0.625 0.531,0.625 0.406,0.625 false 0.646,1.802 0.521,1.688 0.521,1.688 0.396,1.688 false 0.979,3.135 1.292,3.292 0.313,0.156 10 false *a 0.083,0.531 0.542,0.729 0.458,0.198 10 false SST 0.052,1.604 0.51,1.802 0.458,0.198 10 false SST
*a Bush Positioning Protrusion


Using SST and a press, install a new bush.

SST
09710-20011  (09710-03081)
09726-27012  (09726-02041)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 4.INSTALL FRONT NO. 1 LOWER ARM BUSH

a.
C116215C01
3.031,3.99 3.063,4 0.031,0.01 2.969,3.99 3,3.99 0.031,0 3.021,3.5 3.052,3.51 0.031,0.01 2.969,3.49 3,3.5 0.031,0.01 0.917,1.292 0.573,1.292 false 0.573,1.292 0.917,1.49 false 1.406,2.74 1.177,2.167 true 2.792,3.781 3,4.198 false 3,4.198 3.24,3.781 false 0.208,1.219 0.521,1.365 0.313,0.146 10 false SST 1.26,2.781 1.573,2.927 0.313,0.146 10 false SST 2.927,4.208 3.198,4.385 0.271,0.177 10 false *a
*a Bush Positioning Protrusion


Using SST and a press, press in a new bush.

SST
09710-20011  (09710-06071)
09710-22021  (09710-01071)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 5.INSTALL FRONT LOWER BALL JOINT ATTACHMENT

a.

Install the ball joint attachment with the nut and a new cotter pin.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 6.TEMPORARILY INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F050008C02
0.833,0.896 1.802,0.281 1.802,0.281 2.583,0.75 true 1.74,0.104 2.052,0.26 0.313,0.156 10 false *1
*1 Matchmark


a.

Temporarily install the lower arm, and No. 1 and No. 2 camber adjusting cams with the 2 camber adjusting cams and 2 nuts.


b.

Align the matchmarks on the No. 1 camber adjusting cam and No. 2 camber adjusting cam with the corresponding matchmarks on the vehicle frame.


c.

Install the ball joint attachment with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Temporarily install the shock absorber with coil spring with the bolt and nut.


Hide 10.TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

a.

Tighten the 2 nuts.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 11.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 12.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT