Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM(for 4WD and Pre-Runner) › 2012.04–2012.10
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052580 FRONT UPPER SUSPENSION ARM(for 4WD and Pre-Runner) A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT UPPER BALL JOINT

a.
C237641N01
2.063,0.219 1.719,0.219 false 1.719,0.219 0.99,0.813 false 0.99,2.406 0.792,2.406 0.792,2.406 0.729,2 false 2.094,0.146 2.5,0.333 0.406,0.188 10 false SST 1.073,2.323 1.479,2.51 0.406,0.188 10 false SST

Using SST and a press, press in a new upper ball joint.

SST
09612-30012  
09223-00010  


b.

Using a snap ring expander, install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



Hide 2.INSTALL UPPER BALL JOINT DUST COVER

a.
C159213C04
2.5,0.938 2.5,1.719 false 1.896,1.25 1.99,1.25 false 1.427,1.25 1.521,1.25 false 2.5,0.938 2.063,0.938 true 2.5,1.458 2.208,1.458 false 2.208,1.458 1.969,1.26 false 1.427,1.25 0.979,1.25 false 0.75,1.167 0.958,1.313 0.208,0.146 10 false *1 2.375,1.75 2.583,1.896 0.208,0.146 10 false *1
*1 MP grease No. 2


Pack the upper arm ball joint with MP grease No. 2.

Grease capacity:

8.0 g (0.282 oz.)



b.

Apply MP grease No. 2 to the locations shown in the illustration.

NOTICE:

Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.



c.

Install a new dust cover to the upper arm.


d.

Install a new dust cover set ring.


Hide 3.INSTALL FRONT UPPER ARM BUSH

a.
F050004
0.521,0.229 0.781,0.229 false 0.781,0.229 0.885,0.406 false 0.156,0.125 0.49,0.323 0.333,0.198 10 false SST

Using SST and a press, press in a new upper arm bush.

SST
09710-30021  (09710-03101)


Hide 4.TEMPORARILY INSTALL FRONT UPPER SUSPENSION ARM ASSEMBLY LH

C280973C01
1.198,1.646 1.438,1.844 0.24,0.198 10 true *1
*1 Nut


a.

Temporarily install the upper arm and 2 retainers with the bolt and nut.

HINT:

Fix the nut in place and temporarily install the bolt.



b.

Install the upper arm to the steering knuckle with the nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


c.

Install a new clip.


Hide 5.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the stabilizer link to the steering knuckle with the nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 6.CONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.

Install the 2 bolts and connect the speed sensor wire.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 7.INSTALL FRONT WHEEL

a.

Install the front wheel.

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)


Hide 9.TIGHTEN FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Tighten the bolt of the upper arm.

Torque:
115 N*m (1173 kgf*cm, 85 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 10.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT