Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/ VSC) › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052592 BRAKE ACTUATOR(w/ VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ VSC)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 3 BRAKE ACTUATOR BRACKET

a.
C280588
2.438,1.958 2.594,2.156 0.156,0.198 10 A

Install the No. 3 brake actuator bracket with the bolt.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not install the bolt for the hole labeled A as it is installed together with the actuator with bracket.



Hide 2.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C280589
3.031,2.677 3.188,2.875 0.156,0.198 10 A 1.313,2.729 1.469,2.927 0.156,0.198 10 B 0.875,1.677 1.031,1.875 0.156,0.198 10 C

Install the actuator with bracket with the 2 bolts and nut.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the 2 bolts and nut uniformly in alphabetical order.

·

Be careful not to damage the brake tubes.

·

Do not drop the actuator. If dropped, replace it.




b.
C247704
2.115,1.115 2.281,0.771 2.281,0.771 2.458,0.771 false 1.906,1.073 1.906,0.375 1.906,0.375 2.167,0.375 false 1.688,1.021 1.688,0.219 1.688,0.219 1.583,0.219 false 1.375,1 1.01,0.385 1.01,0.385 0.781,0.385 false 1.5,1.396 1.5,3.073 1.5,3.073 2.24,3.073 false 1.771,1.458 1.771,3.063 false 2.24,0.281 2.563,0.479 0.323,0.198 10 *1 2.5,0.688 2.792,0.833 0.292,0.146 10 *2 0.594,0.302 0.865,0.479 0.271,0.177 10 *3 1.396,0.146 1.667,0.313 0.271,0.167 10 *4 2.26,2.979 2.594,3.208 0.333,0.229 10 *5

Set each brake line in the correct position on the brake actuator as shown in the illustration.

HINT:
·

*1: to front wheel cylinder RH

·

*2: to front wheel cylinder LH

·

*3: to rear wheel cylinder RH

·

*4: to rear wheel cylinder LH

·

*5: from master cylinder




c.

Using a union nut wrench, connect the 6 brake lines.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Connect the actuator connector and push the lock lever downward.


Hide 4.BLEED CLUTCH LINE (for Manual Transmission)

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 6.CHECK BRAKE ACTUATOR WITH INTELLIGENT TESTER