This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1241/41 | Low Battery Positive Voltage or Abnormally High Battery Positive Voltage | Either condition is met:
1.
Both conditions continue for at least 10 seconds. ·
Vehicle speed is more than 3 km/h (2 mph). ·
The IG1 terminal voltage is below 9.5 V. 2.
All conditions continue for at least 0.2 seconds ·
Solenoid relay remains on. ·
Relay contact is open. ·
The IG1 terminal voltage is below 9.5 V. |
·
ECU-IG&GAUGE fuse ·
Battery ·
Charging system ·
Power source circuit ·
Internal power supply circuit of skid control ECU (Brake actuator assembly) |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before disconnecting the connector, make sure that there are no problems with the connection.
After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
Check the battery voltage.
11 to 14 V
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1KD-FTV) | B |
| NG (for 2KD-FTV) | C |
| NG (for 2TR-FE) | D |
| NG (for 2TR-FBE) | E |
A
B
C
D
E
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A13-25 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-2 (GND1) - Body ground | Always | Below 1 Ω |
| A13-24 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC not output | A |
| DTC output | B |
If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B