Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1249/49  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting open circuits in the stop light input line of the stop light LH and RH circuits or an open in the ground line with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1249/49 Open in Stop Light Switch Circuit When the IG1 terminal voltage is 9.5 V or higher, either condition continues for 0.3 seconds or more.
·

Open circuits in the stop light LH and RH circuits.

·

An open circuit in the ground line of the stop light LH and RH circuits.


·

Stop light switch circuit

·

Stop light LH and RH circuits

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C237094
0.677,0.813 2.167,1.01 1.49,0.198 10 false from Stop Light Switch 4.563,0.698 4.813,0.854 0.25,0.156 10 false 10 4.854,0.708 5.198,0.906 0.344,0.198 10 false STP 4.865,1.75 5.469,1.948 0.604,0.198 10 false GND1 4.865,2.094 5.469,2.292 0.604,0.198 10 false GND2 4.615,1.625 4.802,1.792 0.188,0.167 10 false 2 4.552,1.969 4.781,2.177 0.229,0.208 10 false 24 5.552,1.25 6.167,1.844 0.615,0.594 10 false Open Detection Circuit 4.833,2.813 5.208,3.01 0.375,0.198 10 false A13 4.833,3.021 6.406,3.448 1.573,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 0.896,1.656 1.135,1.854 0.24,0.198 10 false L2 0.896,1.844 2.094,2.615 1.198,0.771 10 false Stop Light LH (Rear Combination Light Assembly LH) 2.646,1.677 2.885,1.875 0.24,0.198 10 false L1 2.646,1.844 3.833,2.917 1.188,1.073 10 false Stop Light RH (Rear Combination Light Assembly RH) 0.49,1.917 0.615,2.052 0.125,0.135 10 false 4 0.49,2.719 0.646,2.958 0.156,0.24 10 false 3 2.229,1.906 2.354,2.042 0.125,0.135 10 false 4 2.219,2.708 2.49,2.958 0.271,0.25 10 false 3 2.313,2.125 2.469,2.292 0.156,0.167 10 false B 2.313,2.479 2.469,2.646 0.156,0.167 10 false E 0.573,2.125 0.729,2.292 0.156,0.167 10 false B 0.573,2.479 0.729,2.646 0.156,0.167 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light LH and RH come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 8 84

f.

Using the intelligent tester, check the input of the stop light switch operation when the brake pedal is operated.

OK:

When the brake pedal is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C117862
1.542,0.646 1.875,0.885 0.333,0.24 2.385,2.813 2.292,2.813 2.292,2.813 2.313,1.896 false 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.594,0.688 2.01,0.917 0.417,0.229 10 false A13 2.448,2.719 2.865,2.948 0.417,0.229 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-10 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR