Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1248/48  Open Circuit in Rear Differential Lock  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1248/48 Open Circuit in Rear Differential Lock At a vehicle speed of 50 km/h (31 mph) or more, 3 seconds or more elapse after the rear differential changes from free to lock.
HINT:

For vehicles without rear differential lock, this DTC may be stored due to an EXI2 terminal circuit malfunction.


·

EXI2 terminal circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C237408
5.365,1.385 5.708,1.542 0.344,0.156 10 false A13 5.365,1.563 7.01,1.917 1.646,0.354 10 false Skid Control ECU (Brake Actuator Assembly) 5.646,0.729 5.969,0.896 0.323,0.167 10 false EXI2 5.323,0.625 5.521,0.792 0.198,0.167 10 false 22 1.438,0.74 2.406,0.927 0.969,0.188 10 false from IG Circuit

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (EXI2 TERMINAL)
a.
C117862
1.521,0.656 1.865,0.917 0.344,0.26 2.438,2.823 2.604,2.823 2.604,2.823 2.615,2.063 false 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.583,0.698 1.99,0.938 0.406,0.24 10 false A13 2.115,2.76 2.521,3 0.406,0.24 10 false EXI2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-22 (EXI2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 50 km/h (31 mph) or more for 3 seconds or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

B