Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  U0073  Control Module Communication Bus OFF  U0100  Lost Communication with ECM / PCM  U0123  Lost Communication with Yaw Rate Sensor Module  U0124  Lost Communication with Lateral Acceleration Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM, steering angle sensor (spiral cable sub-assembly) and yaw rate sensor assembly via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus OFF One of the following conditions is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, after the output of data from the skid control ECU is completed, the sending operation continues for 5 seconds or more.

2.

The condition that the bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession (sent signals cannot be received).

3.

When the IG1 terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate and acceleration sensor and the steering angle sensor continues for 1 second or more.

4.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that a delay in receiving data from the yaw rate and acceleration sensor and the steering angle sensor occurs more than once within 5 seconds.



CAN communication system
U0100 Lost Communication with ECM / PCM Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more.


CAN communication system
U0123 Lost Communication with Yaw Rate Sensor Module Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the yaw rate sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that data from the yaw rate sensor cannot be received occurs once or more within 5 seconds.



CAN communication system
U0124 Lost Communication with Lateral Acceleration Sensor Module Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.



CAN communication system
U0126 Lost Communication with Steering Angle Sensor Module Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.



CAN communication system

PROCEDURE

1.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If a CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS and VSC) after the CAN communication system returns to normal.


Result:
Result Proceed to
DTC (relating to CAN communication system) is output A
DTC (relating to ABS and/or VSC system) is output B
DTC is not output C




A

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C