Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Signals from the steering angle sensor (spiral cable sub-assembly) are sent to the skid control ECU (brake actuator assembly) via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1432 Steering Angle Sensor Power Source Voltage Malfunction A steering angle sensor power supply malfunction signal is received from the steering angle sensor.
·

ECU-B fuse

·

ECU-IG&GAUGE fuse

·

Steering angle sensor power supply

·

Steering angle sensor circuit

·

Steering angle sensor (Spiral cable sub-assembly)



WIRING DIAGRAM

C200080
3.938,0.823 4.854,1.208 0.917,0.385 10 false from Battery 3.927,1.469 5.073,1.792 1.146,0.323 10 false from IG1 Circuit 0.896,0.813 1.365,1.146 0.469,0.333 10 false BAT 1.01,1.479 1.313,1.771 0.302,0.292 10 false IG 0.875,1.792 1.24,1.99 0.365,0.198 10 false ESS 1.323,0.698 1.563,0.896 0.24,0.198 10 false 6 1.323,1.344 1.542,1.542 0.219,0.198 10 false 5 1.323,1.656 1.5,1.813 0.177,0.156 10 false 2 0.229,2.531 3.531,2.74 3.302,0.208 10 false Steering Angle Sensor (Spiral Cable Sub-assembly) 0.854,3.479 2.958,3.74 2.104,0.26 10 false : CAN Communication System 5.51,2.26 7.094,2.656 1.583,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 5.51,2.073 6.469,2.271 0.958,0.198 10 false A36 0.229,2.344 0.531,2.51 0.302,0.167 10 false G83 2.031,1.646 3.354,2.208 1.323,0.563 10 false ECU-IG&GAUGE 2.25,0.99 2.844,1.24 0.594,0.25 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral cable sub-assembly.

·

After replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



HINT:
·

When DTC U0073 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).

·

When the speed sensor or yaw rate sensor assembly has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensor or the yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


c.
C197050
0.323,1.156 0.667,1.396 0.344,0.24 2.365,1.396 2.667,1.74 true 0.156,0.115 0.469,0.271 0.313,0.156 10 false *a 0.365,1.208 0.823,1.469 0.458,0.26 10 false G83 2.708,1.688 3.167,1.948 0.458,0.26 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral Cable Sub-assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G83-6 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


c.
C197050
0.375,1.083 0.698,1.313 0.323,0.229 1.833,1.792 2.115,1.406 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.417,1.115 0.833,1.354 0.417,0.24 10 false G83 1.667,1.74 2.083,1.979 0.417,0.24 10 false IG
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral Cable Sub-assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G83-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-2 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR