Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for TSAM Made) › 2012.04–2013.10
RM1840EF _54 Brake _009624 BRAKE SYSTEM (OTHER) _0052621 BRAKE MASTER CYLINDER(for TSAM Made) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for TSAM Made)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C122648
1.458,0.458 0.844,0.458 false 1.563,1.469 1.573,1.583 1.573,1.583 1.771,1.583 false 0.635,0.375 0.792,0.531 0.156,0.156 10 false *1 1.813,1.479 2,1.635 0.188,0.156 10 false *2 0.51,1.854 0.698,2.031 0.188,0.177 10 false *3
*1 Grommet
*2 Master Cylinder
*3 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the 2 new grommets and install them to the master cylinder.


b.

Install the reservoir with the screw.


Hide 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS)

a.

Install a new O-ring to the master cylinder.


b.
C122645

Install the master cylinder and bracket (with 4-way) to the booster with the 2 nuts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


c.
C281950
2.281,0.333 2.438,0.531 0.156,0.198 10 false A 2.094,1.302 2.25,1.5 0.156,0.198 10 false C 1.156,0.625 1.313,0.823 0.156,0.198 10 false B 1.74,1.01 1.896,1.208 0.156,0.198 10 true C 1.417,1.438 1.573,1.635 0.156,0.198 10 true C 0.719,1.146 0.875,1.344 0.156,0.198 10 false C 0.635,1.25 0.792,1.448 0.156,0.198 10 false C

Using a union nut wrench, connect the 6 brake lines labeled C to the brake master cylinder and 4-way.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Connect the brake fluid level warning switch connector labeled B to the master cylinder.


e.

Connect the clutch reservoir tube labeled A to the master cylinder.


Hide 3.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)

a.

Install a new O-ring to the master cylinder.


b.
C122647

Install the master cylinder and bracket (with 3-way) to the booster with the 2 nuts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


c.
C281950
2.281,0.333 2.438,0.531 0.156,0.198 10 false A 2.094,1.302 2.25,1.5 0.156,0.198 10 false C 1.156,0.625 1.313,0.823 0.156,0.198 10 false B 1.74,1.01 1.896,1.208 0.156,0.198 10 true C 1.417,1.438 1.573,1.635 0.156,0.198 10 true C 0.719,1.146 0.875,1.344 0.156,0.198 10 false C 0.635,1.25 0.792,1.448 0.156,0.198 10 false C

Using a union nut wrench, connect the 5 brake lines labeled C to the master cylinder and 3-way.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Connect the brake fluid level warning switch connector labeled B to the master cylinder.


e.

for Manual Transmission:

Connect the clutch reservoir tube labeled A to the master cylinder.


Hide 5.BLEED AIR FROM CLUTCH LINE (for Manual Transmission)