Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 2WD) › from 2012.10
RM1840EF _54 Brake _009625 BRAKE (FRONT) _0052627 FRONT BRAKE(for 2WD) A

BRAKE (FRONT)  FRONT BRAKE(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT DISC

a.
C111369
1.677,1.115 0.906,0.344 0.906,0.344 0.771,0.344 true 1.677,1.24 0.906,0.344 true 0.604,0.271 0.75,0.406 0.146,0.135 10 false *1
*1 Matchmark


Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



Hide 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

a.

Install the disc brake cylinder mounting with the 2 bolts.

Torque:
117 N*m (1193 kgf*cm, 86 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 pad support plates to the cylinder mounting.


Hide 4.INSTALL PAD WEAR INDICATOR PLATE

a.

Install the pad wear indicator plate to the inner lower side of the pad.


Hide 5.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C285351
0.417,1.063 0.417,1.646 false 0.99,1.417 0.99,2 false 1.594,1.823 1.594,2.406 false 1.594,2.073 2.146,2.073 false 2.49,1.583 2.49,1.167 2.49,1.167 2.677,1.167 false 3.208,2.833 3.208,3.052 3.208,3.052 2.885,3.052 false 0.646,2.917 0.844,3.104 0.198,0.188 10 false *4 0.344,1.667 0.563,1.865 0.219,0.198 10 false *2 0.906,2.042 1.135,2.229 0.229,0.188 10 false *1 1.521,2.406 1.719,2.604 0.198,0.198 10 false *3 2.667,2.979 2.885,3.177 0.219,0.198 10 false *2 2.677,1.052 2.906,1.24 0.229,0.188 10 false *1
*1 No. 1 Anti-squeal Shim
*2 No. 2 Anti-squeal Shim
*3 Front Disc Brake Pad
*4 Disc brake grease


Apply a light coat of disc brake grease to both sides of each No. 1 anti-squeal shim.


b.

Install the No. 1 anti-squeal shims and No. 2 anti-squeal shims to the pads.

NOTICE:
·

When replacing a worn pad, the shims must be replaced together with the pads.

·

Install the shims in the correct positions and directions as shown in the illustration.




Hide 6.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 disc brake pads to the cylinder mounting.

NOTICE:

Make sure there is no oil or grease on the friction surfaces of the pads and disc.



Hide 7.INSTALL NO. 1 COLLAR

a.
C238093
2.219,0.917 2.219,1.354 2.219,1.354 2.521,1.354 false 1.042,1.073 0.771,1.188 0.771,1.188 0.521,1.188 false 2.563,1.26 2.729,1.396 0.167,0.135 10 false *1 0.333,1.094 0.49,1.229 0.156,0.135 10 false *2 0.719,1.656 0.896,1.792 0.177,0.135 10 false *3
*1 No. 1 Collar
*2 No. 2 Collar
*3 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the No. 1 collar.


b.

Install the No. 1 collar to the disc brake cylinder assembly.


Hide 8.INSTALL NO. 2 COLLAR

a.

Apply a light coat of lithium soap base glycol grease to the No. 2 collar.


b.

Install the No. 2 collar to the disc brake cylinder assembly.


Hide 9.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C238094
0.708,2.885 0.875,3.031 0.167,0.146 10 false *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the entire circumference of 4 new front disc brake bush dust boots where they contact the disc brake cylinder, and the entire inner circumference of both ends of the boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the front disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the front disc brake bush dust boot and disc brake cylinder contact surfaces.



b.

Install the 4 front disc brake bush dust boots to the disc brake cylinder assembly.


Hide 10.INSTALL NO. 1 CYLINDER SLIDE BUSH

a.
C238095
2.531,1.188 2.531,1.625 2.531,1.625 2.906,1.625 false 0.969,1.156 0.688,1.333 0.688,1.333 0.5,1.333 false 0.719,1.656 0.875,1.792 0.156,0.135 10 false *3 2.938,1.531 3.094,1.667 0.156,0.135 10 false *1 0.292,1.25 0.448,1.385 0.156,0.135 10 false *2
*1 No. 1 Cylinder Slide Bush
*2 No. 2 Cylinder Slide Bush
*3 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the No. 1 cylinder slide bush.


b.

Install the No. 1 cylinder slide bush to the disc brake cylinder assembly.


Hide 11.INSTALL NO. 2 CYLINDER SLIDE BUSH

a.

Apply a light coat of lithium soap base glycol grease to the No. 2 cylinder slide bush.


b.

Install the No. 2 cylinder slide bush to the disc brake cylinder assembly.


Hide 12.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.

Install the disc brake cylinder with the 2 bolts.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 13.CONNECT FRONT FLEXIBLE HOSE

a.

Install a new gasket and connect the flexible hose with a new union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

Insert the flexible hose lock securely into the lock hole in the cylinder.



Hide 16.INSTALL FRONT WHEEL

Torque:
152 N*m (1550 kgf*cm, 112 ft.*lbf)