Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE(for 4WD and Pre-Runner) › from 2012.10
RM1840EF _54 Brake _009627 PARKING BRAKE _0052635 PARKING BRAKE CABLE(for 4WD and Pre-Runner) A

PARKING BRAKE  PARKING BRAKE CABLE(for 4WD and Pre-Runner)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE REAR WHEEL

Hide 6.REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 1 parking brake cable from the parking brake lever (See page Brake>PARKING BRAKE>PARKING BRAKE LEVER>REMOVAL).


b.

Remove the 2 bolts and No. 1 heat insulator.


c.

Remove the No. 1 clip and pin from the No. 3 parking brake cable.

C237687
4.406,0.49 2.313,0.49 true 2.979,3.146 2.979,1.729 2.979,1.729 2.323,1.729 true 4.438,2.302 2.969,1.094 2.969,1.094 2.563,1.094 true 5.823,2.552 5.583,2.323 5.583,2.323 5.438,2.323 false 2.115,0.396 2.385,0.563 0.271,0.167 10 false *3 2.385,1.01 2.646,1.167 0.26,0.156 10 false *2 2.146,1.635 2.427,1.813 0.281,0.177 10 false *1 5.271,2.219 5.531,2.385 0.26,0.167 10 false *4
*1 No. 1 Parking Brake Cable *2 No. 3 Parking Brake Cable
*3 Parking Brake Equalizer *4 Cable Support Bracket



d.

Disconnect the No. 1 parking brake cable from the No. 3 parking brake cable.


e.

Disconnect the No. 1 parking brake cable from the parking brake equalizer.


f.

Remove the bolt holding the No. 1 parking brake cable.


g.

Remove the No. 1 parking brake cable clamp from the No. 1 parking brake cable.


h.

Remove the No. 1 parking brake cable from the cable support bracket.


i.

Remove the No. 1 parking brake cable.


Hide 7.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 2 parking brake cable from the parking brake shoe lever RH and backing plate RH.

i.

Disconnect the No. 2 parking brake cable from the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE(for 4WD and Pre-Runner)>DISASSEMBLY).

HINT:

Use the same procedure described for the LH side.



ii.

Remove the 2 bolts and disconnect the No. 2 parking brake cable from the backing plate.



b.

Disconnect the No. 2 parking brake cable from the parking brake equalizer.

C237688
4.323,1.375 4.323,0.427 4.323,0.427 4.094,0.427 true 0.906,2.781 0.906,3.063 false 3.875,0.354 4.042,0.51 0.167,0.156 10 false *1 0.844,3.073 1.01,3.229 0.167,0.156 10 false *2
*1 No. 2 Parking Brake Cable *2 Parking Brake Equalizer



c.

Remove the 4 bolts and No. 2 parking brake cable.


Hide 8.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 3 parking brake cable from the parking brake shoe lever LH and backing plate LH.

i.

Disconnect the No. 3 parking brake cable from the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE(for 4WD and Pre-Runner)>DISASSEMBLY).


ii.

Remove the 2 bolts and disconnect the No. 3 parking brake cable from the backing plate.



b.

Remove the No. 3 clip.

C237689
2.01,0.708 2.01,0.573 2.01,0.573 1.719,0.573 false 4.948,6.073 4.948,6.49 4.948,6.49 5.656,6.49 false 1.5,0.479 1.667,0.646 0.167,0.167 10 false *2 5.75,6.406 5.917,6.573 0.167,0.167 10 false *1
*1 No. 3 Parking Brake Cable *2 No. 3 Clip



c.

Remove the 3 bolts, nut and No. 3 parking brake cable.