Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2012.01–2012.04
RM1840EF _58 Vehicle Interior _009640 DOOR LOCK _0052687 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Hide 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

Hide 3.INSTALL REAR DOOR LOCK ASSEMBLY LH

a.

Install a new door lock wiring harness seal to the rear door lock assembly.

NOTICE:
·

When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water into the connection. This may result in a malfunction of the rear door lock assembly.




b.

Apply MP grease to the sliding parts of the rear door lock assembly.


c.

Insert the rear door lock assembly into the rear door outside handle release plate, and set it on the rear door panel.


d.

Check that the rear door outside handle release plate is securely connected to the rear door lock assembly.


e.
B277533

Using a T30 "TORX" wrench, install the rear door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Connect the door lock connector.


g.

Attach the claw to connect the rear door lock remote control cable assembly to the door lock link clamp.


h.
B342251
2.146,0.281 2.406,0.281 2.406,0.281 2.583,0.438 true 1.5,0.365 1.698,0.365 1.698,0.365 1.885,0.563 true 2.406,0.698 2.552,0.875 2.552,0.875 2.719,0.875 true 2.75,0.802 2.99,1.021 0.24,0.219 11 false *2 1.99,0.167 2.167,0.385 0.177,0.219 11 false *1 1.323,0.26 1.5,0.479 0.177,0.219 11 false *3
*1 Rear Door Inside Locking Cable Assembly LH
*2 Rear Door Lock Remote Control Cable Assembly
*3 Door Lock Link Clamp


Attach the claw to connect the rear door inside locking cable assembly to the door lock link clamp.


Hide 4.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 5.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 6.INSTALL REAR DOOR GLASS RUN LH

Hide 7.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 8.INSTALL REAR DOOR NO. 2 TRIM BRACKET

Hide 9.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

Hide 10.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 11.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).