Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052695 BLOCKING SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  B1586  Open in Immobiliser Communication Circuit  


DESCRIPTION

When the communication line (EFIO - BLK4) between the transponder key ECU assembly and telephone transceiver assembly is stuck on HI output while ignition switch is ON, the telephone transceiver assembly stores DTC B1586.

HINT:

Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1586 Open in Immobiliser Communication Circuit The communication line (EFIO - BLK4) between the transponder key ECU assembly and telephone transceiver assembly is stuck on HI while ignition switch is ON.
·

Telephone transceiver assembly

·

Transponder key ECU assembly

·

ECM

·

Harness or connector



WIRING DIAGRAM

B294527
2.552,2.979 4.646,3.177 2.094,0.198 10 false Telephone Transceiver Assembly 0.042,3.083 1.74,3.281 1.698,0.198 10 false *1: for 1KD-FTV, 2KD-FTV 0.042,3.354 1.74,3.552 1.698,0.198 10 false *2: for 2TR-FBE 2.552,2.802 2.948,2.969 0.396,0.167 10 false G144 6.5,2.385 6.896,2.563 0.396,0.177 10 false ECM 0.917,1.573 1.979,2 1.063,0.427 10 false Transponder Key ECU Assembly 0.906,1.417 1.188,1.583 0.281,0.167 10 false G26 2.979,0.688 3.354,0.854 0.375,0.167 10 false BLK1 2.833,0.677 2.948,0.844 0.115,0.167 10 false 1 1.875,0.698 2.073,0.865 0.198,0.167 10 false 12 2.833,0.969 2.948,1.135 0.115,0.167 10 false 2 4.271,1.625 4.385,1.792 0.115,0.167 10 false 7 4.271,1.917 4.385,2.083 0.115,0.167 10 false 8 5.958,1.51 6.302,1.677 0.344,0.167 10 false 32*2 5.917,1.719 6.292,1.885 0.375,0.167 10 false G146 5.917,2.01 6.292,2.177 0.375,0.167 10 false G146 5.958,2.229 6.271,2.396 0.313,0.167 10 false 31*2 5.563,1.51 5.906,1.677 0.344,0.167 10 false 29*1 5.552,1.719 5.854,1.885 0.302,0.167 10 false G38 5.552,2.021 5.854,2.188 0.302,0.167 10 false G38 5.573,2.229 5.885,2.396 0.313,0.167 10 false 30*1 4.635,0.542 5.115,0.708 0.479,0.167 10 false ECU-B 5.354,0.542 5.708,0.708 0.354,0.167 10 false DCC 1.875,0.99 2.073,1.156 0.198,0.167 10 false 13 0.875,0.844 1.073,1.01 0.198,0.167 10 false 16 1.552,0.771 1.865,0.938 0.313,0.167 10 false EFII 1.5,1.063 1.854,1.229 0.354,0.167 10 false EFIO 1.104,0.938 1.427,1.104 0.323,0.167 10 false GND 2.979,0.969 3.354,1.135 0.375,0.167 10 false BLK4 3.833,1.625 4.208,1.792 0.375,0.167 10 false BLK2 4.24,0.323 4.417,0.49 0.177,0.167 10 false 12 3.99,0.417 4.188,0.583 0.198,0.167 10 false +B 4.26,2.271 4.438,2.438 0.177,0.167 10 false 9 4.083,2.344 4.198,2.51 0.115,0.167 10 false E 6.271,0.417 7.104,0.688 0.833,0.271 10 false from Battery 4.708,0.844 5.01,1.01 0.302,0.167 10 false IGN 4.26,0.625 4.438,0.792 0.177,0.167 10 false 6 3.958,0.698 4.219,0.865 0.26,0.167 10 false IG2 5.438,0.698 6.656,1.125 1.219,0.427 10 false from Ignition Switch Assembly 3.833,1.917 4.208,2.083 0.375,0.167 10 false BLK3 2.99,2.177 3.969,2.563 0.979,0.385 10 false Communication Switch 6.333,1.719 6.708,1.885 0.375,0.167 10 false IMO 6.333,2.01 6.708,2.177 0.375,0.167 10 false IMI

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the telephone transceiver assembly, transponder key ECU assembly or ECM, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

DTC B1586 is not output.


Result:
Result Proceed to
DTC B1586 is output A
DTC B1586 and other DTCs are output B




A

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM)

B

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM)
a.

Disconnect the G144 telephone transceiver assembly connector.


b.

Disconnect the G38*1or G146*2 ECM connector.

*1: for 1KD-FTV, 2KD-FTV

*2: for 2TR-FBE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G144-8 (BLK3) - G38-30 (IMI) Always Below 1 Ω
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FBE:
Tester Connection Condition Specified Condition
G144-8 (BLK3) - G146-31 (IMI) Always Below 1 Ω
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always Below 1 V

for 2TR-FBE:
Tester Connection Condition Specified Condition
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU)
a.

Disconnect the G144 telephone transceiver assembly connector.


b.

Disconnect the G26 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G144-2 (BLK4) - G26-13 (EFIO) Always Below 1 Ω
G144-2 (BLK4) or G26-13 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G144-2 (BLK4) or G26-13 (EFIO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.
B257265
0.667,1.146 1.052,1.469 0.385,0.323 0.823,1.927 0.969,1.917 0.969,1.917 1.281,1.531 true 1.135,2.229 1.323,2.229 1.323,2.229 1.552,1.531 true 0.135,2.385 0.448,2.542 0.313,0.156 10 false *1 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.708,1.219 1.167,1.417 0.458,0.198 10 false G26 0.49,1.844 0.896,2.021 0.406,0.177 10 false GND 0.792,2.146 1.406,2.344 0.615,0.198 10 false EFIO 0.271,3.354 0.729,3.552 0.458,0.198 10 false GND
*1 Waveform
*a Component with harness connected
(Transponder Key ECU Assembly)


Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10V/DIV., 100 ms./DIV.
Condition Ignition switch ON


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - BATTERY AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - BATTERY AND BODY GROUND)
a.
B263444
0.667,0.969 1.125,1.26 0.458,0.292 1.302,1.813 1.458,1.813 1.458,1.813 1.677,1.292 true 2.156,0.969 2.396,0.594 2.396,0.594 2.563,0.583 true 2.135,1.292 2.313,1.802 2.313,1.802 2.542,1.802 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.604,0.5 3.219,0.698 0.615,0.198 10 false IG2 1.188,1.74 1.5,1.927 0.313,0.188 10 false E 2.573,1.719 3.188,1.917 0.615,0.198 10 false +B 0.719,1.042 1.333,1.24 0.615,0.198 10 false G144
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the G144 telephone transceiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G144-9 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G144-12 (+B) - G144-9 (E) Always 11 to 14 V
G144-6 (IG2) - G144-9 (E) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

DTC B1586 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM IS DEFECTIVE)

NG

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

12.REGISTER ECU COMMUNICATION ID
12.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

DTC B1586 is not output.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY