Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Gauge Malfunction  


DESCRIPTION

In this circuit, the meter CPU receives engine coolant temperature signals from the ECM. The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E273646
0.563,2.125 1.063,2.323 0.5,0.198 10 false ECM 0.781,1.104 1.281,1.302 0.5,0.198 10 false THWO 1.417,0.865 1.667,1.052 0.25,0.188 10 false 2*1 1.833,0.865 2.135,1.063 0.302,0.198 10 false 14*2 2.333,0.875 2.667,1.063 0.333,0.188 10 false 26*3 1.396,1.083 1.75,1.281 0.354,0.198 10 false G39 1.854,1.094 2.167,1.333 0.313,0.24 10 false G88 2.333,1.094 2.625,1.271 0.292,0.177 10 false C97 0.125,2.688 1.906,2.958 1.781,0.271 10 false *1: for 1KD-FTV, 2KD-FTV 0.135,2.99 1.917,3.26 1.781,0.271 10 false *2: for 2TR-FE 0.125,3.302 1.906,3.573 1.781,0.271 10 false *3: for 2TR-FBE 5.74,0.979 5.885,1.177 0.146,0.198 10 false 4 5.969,1.104 6.427,1.292 0.458,0.188 10 false TEMP 5.854,2.177 6.313,2.365 0.458,0.188 10 false G19 5.865,2.354 7.042,2.792 1.177,0.438 10 false Combination Meter Assembly

PROCEDURE

1.CHECK FOR DTC

*1: for 1KD-FTV, 2KD-FTV

*2: for 2TR-FE, 2TR-FBE


a.

Check for DTCs of the ECD system*1 or SFI system*2.


Result:
Result Proceed to
DTC is output (for 1KD-FTV, 2KD-FTV) A
DTC is output (for 2TR-FE, 2TR-FBE) B
DTC is not output C




A

2.CHECK ENGINE TYPE

B

3.CHECK ENGINE TYPE

C

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
2.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for 1KD-FTV, w/ EGR Cooler A
for 1KD-FTV, w/o EGR Cooler B
for 2KD-FTV, w/ EGR Cooler C
for 2KD-FTV, w/o EGR Cooler D




A

B

C

D

3.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for 2TR-FE, w/ Secondary Air Injection System A
for 2TR-FE, w/o Secondary Air Injection System B
for 2TR-FBE C




A

B

C

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G39*1, G88*2 or C97*3 ECM connector.

*1: for 1KD-FTV, 2KD-FTV

*2: for 2TR-FE

*3: for 2TR-FBE



c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G39-2 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G39-2 (THWO) - Body ground Always 10 kΩ or higher


for 2TR-FE
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G88-14 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G88-14 (THWO) - Body ground Always 10 kΩ or higher

for 2TR-FBE
Tester Connection Condition Specified Condition
G19-4 (TEMP) - C97-26 (THWO) Always Below 1 Ω
G19-4 (TEMP) or C97-26 (THWO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

5.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

OK:

The operation of the engine coolant temperature gauge returns to normal.


Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2KD-FTV) C
NG (for 2TR-FE) D
NG (for 2TR-FBE) E




A

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

B

C

D

E