Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY(for Extra Cab) › from 2012.10
RM1840EF _58 Vehicle Interior _009647 SEAT BELT _0052737 FRONT SEAT OUTER BELT ASSEMBLY(for Extra Cab) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for Extra Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

B084924

a.

Insert the tip of the adjuster into the body as shown in the illustration.


b.

Install the front shoulder belt anchor adjuster assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 2.INSTALL SHOULDER BELT ANCHORAGE PLATE COVER

B342507
1.688,1.167 2.052,0.802 2.052,0.802 2.26,0.802 true 1.729,0.333 2.042,0.531 0.313,0.198 10 false *a 2.271,0.698 2.583,0.896 0.313,0.198 10 false *b
*a Slide
*b Mark


a.

Install the shoulder belt anchorage plate cover as shown in the illustration.

HINT:

Make sure the plate cover is properly set into the garnish guides.



Hide 4.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

B342508

a.

w/o Pretensioner:

Align the front seat outer belt assembly LH positioning holes with the claws.

Install the retractor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B321969
1.896,0.271 2.177,0.5 0.281,0.229 10 false A 1.823,1.458 2.104,1.635 0.281,0.177 10 false B

w/ Pretensioner:

Align the front seat outer belt assembly LH positioning holes with the claws.

Install the retractor of the front seat outer belt assembly LH with the 2 bolts.

Torque:
4.8 N*m (49 kgf*cm, 42 in.*lbf)

for bolt A


Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

for bolt B



c.
B342493

w/ Pretensioner:

Connect the pretensioner connector as shown in the illustration.


d.
B084920

Install the shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Attach the cap.


Hide 5.INSTALL QUARTER INSIDE TRIM BOARD LH

a.

Attach the 7 clips, 3 guides and 4 claws to install the quarter inside trim board.


b.

Connect the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Connect the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 11.INSTALL REAR SEAT CUSHION ASSEMBLY LH (w/ Seat Cushion)

Hide 12.INSTALL REAR SEAT CUSHION ASSEMBLY RH (w/ Seat Cushion)

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).