Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on the signal.

WIRING DIAGRAM

E236138
1.365,1.396 1.823,1.542 0.458,0.146 10 false G146 1.365,0.667 1.781,0.813 0.417,0.146 10 false G146 1.427,1.625 1.604,1.771 0.177,0.146 10 false *2 1.427,0.896 1.604,1.042 0.177,0.146 10 false *2 1.448,0.469 1.646,0.615 0.198,0.146 10 false 19 1.448,1.188 1.656,1.333 0.208,0.146 10 false 21 0.146,4.458 2.021,4.615 1.875,0.156 10 false *2: for 2TR-FBE 0.146,4.177 2.021,4.333 1.875,0.156 10 false *1: for 1KD-FTV 6.052,0.677 6.344,0.927 0.292,0.25 10 false AC1 6.042,1.375 6.396,1.573 0.354,0.198 10 false ACT 6.052,2.365 6.427,2.604 0.375,0.24 10 false MGC 2.052,3.469 3.427,3.719 1.375,0.25 10 false Magnet Clutch Relay 0.125,3.563 1.427,3.792 1.302,0.229 10 false from Ignition Switch 5.01,3.688 6.927,4.063 1.917,0.375 10 false Cooler Compressor Assembly 0.458,1.927 0.865,2.104 0.406,0.177 10 false ECM 0.542,0.677 0.906,0.865 0.365,0.188 10 false AC1 0.542,1.417 0.906,1.604 0.365,0.188 10 false ACT 5.417,2.833 5.792,2.979 0.375,0.146 10 false G94 5.729,2.26 5.906,2.406 0.177,0.146 10 false 13 5.01,3.542 5.375,3.688 0.365,0.146 10 false C33 2.052,3.323 2.365,3.469 0.313,0.146 10 false G71 5.802,1.292 5.917,1.438 0.115,0.146 10 false 7 2.979,2.271 3.094,2.417 0.115,0.146 10 false 1 4.781,3.323 4.896,3.469 0.115,0.146 10 false 1 2.188,2.271 2.302,2.417 0.115,0.146 10 false 2 3,2.906 3.115,3.052 0.115,0.146 10 false 3 2.198,2.906 2.313,3.052 0.115,0.146 10 false 5 5.75,0.563 5.927,0.708 0.177,0.146 10 false 21 1.063,0.469 1.26,0.615 0.198,0.146 10 false 18 1.073,1.625 1.25,1.771 0.177,0.146 10 false *1 1.01,1.396 1.302,1.542 0.292,0.146 10 false G38 1.073,0.896 1.25,1.042 0.177,0.146 10 false *1 1.01,0.667 1.302,0.813 0.292,0.146 10 false G38 1.063,1.188 1.292,1.333 0.229,0.146 10 false 19 5.417,2.969 7.042,3.573 1.625,0.604 10 false Air Conditioning Amplifier Assembly 0.49,2.531 1.635,2.708 1.146,0.177 10 false ECU-IG&GAUGE 5.031,4.021 6.948,4.396 1.917,0.375 10 false - Magnet Clutch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL)
a.

Use the Data List to check if the magnet clutch on request signal is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST

ECM
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C Signal Magnet clutch on request signal / ON or OFF ON: A/C switch on
OFF: A/C switch off
Check this item with the engine idling and the blower switch on (LO level).

OK:

Display is as specified in normal condition.



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH RELAY

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
2.INSPECT MAGNET CLUTCH RELAY
a.
E272300
2.667,0.729 3.052,0.563 true 2.01,0.698 1.625,0.51 true 2.333,1.5 1.958,1.865 true 2.448,1.146 3.021,1.667 true 1.51,0.438 1.667,0.635 0.156,0.198 10 false 1 0.385,1.229 0.542,1.427 0.156,0.198 10 false 1 1.417,1.229 1.573,1.427 0.156,0.198 10 false 2 1.427,0.771 1.583,0.969 0.156,0.198 10 false 5 0.385,0.771 0.542,0.969 0.156,0.198 10 false 3 1.875,1.844 2.031,2.042 0.156,0.198 10 false 3 3.094,0.469 3.25,0.667 0.156,0.198 10 false 2 3.094,1.677 3.25,1.875 0.156,0.198 10 false 5

Remove the magnet clutch relay.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY(for Magnet Clutch Control)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.
E272301
0.302,1.042 0.698,1.344 0.396,0.302 1.979,1.438 2.667,1.083 true 2.729,1.01 3.188,1.208 0.458,0.198 10 false MGC 0.146,0.104 0.604,0.302 0.458,0.198 10 false *a 0.375,1.115 0.833,1.313 0.458,0.198 10 false G94
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the G94 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G94-13 (MGC) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 0.76,0.99 1.292,1.729 true 0.802,0.104 1.135,0.281 0.333,0.177 10 false G94 1.313,1.729 1.677,1.917 0.365,0.188 10 false MGC 0.073,0 0.292,0.198 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-13 (MGC) - Body ground
·

Engine idling

·

A/C switch on (magnet clutch on permitted)


Below 1 V
·

Engine idling

·

A/C switch off or on (magnet clutch not on permitted)


11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT MAGNET CLUTCH ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
5.INSPECT MAGNET CLUTCH ASSEMBLY

b.

Apply battery voltage to the magnet clutch and check operation of the magnet clutch.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Ground wire
Magnet clutch engages


Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2TR-FBE) C




A

6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - MAGNET CLUTCH RELAY)

B

C

6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - MAGNET CLUTCH RELAY)
a.

Disconnect the C33 cooler compressor assembly connector.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G71-5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch ON Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G71-3 - C33-1 Always Below 1 Ω
G71-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Disconnect the G38*1 or G146*2 ECM connectors.

*1: for 1KD-FTV

*2: for 2TR-FBE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Condition Specified Condition
G94-21 (AC1) - G38-18 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher

for 2TR-FBE
Tester Connection Condition Specified Condition
G94-21 (AC1) - G146-19 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 0.875,1.198 1.406,1.74 true 0.802,0.104 1.146,0.281 0.344,0.177 10 false G94 1.313,1.76 1.677,1.948 0.365,0.188 10 false AC1 0.073,0.063 0.292,0.26 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-21 (AC1) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V


Result:
Result Proceed to
OK (for 1KD-FTV) A
OK (for 2TR-FBE) B
NG C




A

B

C

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Disconnect the G38*1 or G146*2 ECM connectors.

*1: for 1KD-FTV

*2: for 2TR-FBE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Condition Specified Condition
G94-7 (ACT) - G38-19 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher

for 2TR-FBE
Tester Connection Condition Specified Condition
G94-7 (ACT) - G146-21 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 1.51,0.979 1.406,1.74 true 0.792,0.115 1.135,0.292 0.344,0.177 10 G94 1.229,1.729 1.594,1.917 0.365,0.188 10 ACT 0.073,0 0.292,0.198 0.219,0.198 10 *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-7 (ACT) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


Below 1 V



Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2TR-FBE) C



A

B

C