1. PRECAUTION (w/ Airbag System)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.REMOVE REAR SEAT ASSEMBLY
4.REMOVE FRONT DOOR SCUFF PLATE LH
| *1 | Protective Tape |
Put protective tape around the front door scuff plate.
Using a moulding remover, detach the 7 claws and 3 clips, and remove the front door scuff plate.
5.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
6.REMOVE FRONT DOOR OPENING TRIM LH
Remove the front door opening trim.
7.REMOVE FRONT DOOR OPENING TRIM RH
Use the same procedure described for the LH side.
8.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)
| *1 | Protective Tape |
Use the same procedure for both front No. 1 assist grip plugs.
Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.
Tape the screwdriver tip before use.
9.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)
Use the same procedure described for the LH side.
10.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
Use the same procedure for both assist grips.
Remove the 2 screws and front assist grip.
11.REMOVE FRONT PILLAR GARNISH LH
Detach the 2 clips and 2 guides and remove the front pillar garnish.
12.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
13.REMOVE REAR DOOR SCUFF PLATE LH
| *1 | Protective Tape |
Put protective tape around the rear door scuff plate.
Using a moulding remover, detach the 7 claws and 2 clips, and remove the rear door scuff plate.
14.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
15.REMOVE REAR DOOR OPENING TRIM LH
Remove the rear door opening trim.
16.REMOVE REAR DOOR OPENING TRIM RH
Use the same procedure described for the LH side.
17.REMOVE LOWER CENTER PILLAR GARNISH LH
Remove the bolt and disconnect the front seat outer belt floor anchor.
Detach the 2 claws, 2 guides and 2 clips and remove the lower center pillar garnish.
18.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
19.REMOVE CENTER PILLAR GARNISH LH
| *1 | Protective Tape |
Using a screwdriver, detach the 4 claws and remove the front seat belt shoulder anchor cover.
Tape the screwdriver tip before use.
Remove the bolt and disconnect the front seat belt shoulder anchor.
Detach the clip.
Pull the center pillar garnish in the direction indicated by the arrow in the illustration to detach the guide and remove the center pillar garnish.
20.REMOVE CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
21.REMOVE UPPER BACK PANEL GARNISH
Detach the 4 claws and 5 clips and remove the upper back panel garnish.
22.REMOVE LOWER QUARTER TRIM PANEL LH
Detach the claw and 3 clips and remove the lower quarter trim panel.
23.REMOVE LOWER QUARTER TRIM PANEL RH
Use the same procedure described for the LH side.
24.REMOVE QUARTER INSIDE TRIM BOARD LH
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and open the rear seat belt shoulder anchor cover.
Tape the screwdriver tip before use.
Remove the bolt and disconnect the rear seat belt shoulder anchor.
Detach the 4 clips and remove the quarter inside trim board.
25.REMOVE QUARTER INSIDE TRIM BOARD RH
Use the same procedure described for the LH side.
26.REMOVE MAP LIGHT ASSEMBLY
27.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
28.REMOVE VISOR ASSEMBLY LH
Detach the guide.
Remove the 2 screws and visor.
29.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
30.REMOVE VISOR HOLDER LH
Remove the screw.
Detach the 2 claws and remove the visor holder.
31.REMOVE VISOR HOLDER RH
Use the same procedure described for the LH side.
32.REMOVE ASSIST GRIP
| *1 | Protective Tape |
Use the same procedure for all assist grips.
Using a screwdriver, detach the 4 claws and open the 2 covers.
Tape the screwdriver tip before use.
Remove the 2 screws and assist grip.
33.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
34.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
35.REMOVE NO. 2 HEATER TO REGISTER DUCT
36.REMOVE NO. 1 HEATER TO REGISTER DUCT
37.REMOVE NO. 3 HEATER TO REGISTER DUCT
38.REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)
39.REMOVE BACK WINDOW GLASS
40.REMOVE ROOF HEADLINING ASSEMBLY
Detach the 5 clamps from the front pillar.
Disconnect the connectors and detach the 4 clamps.
| *A | w/o Assist Grip |
Using a clip remover, remove the clips.
Remove the roof headlining as shown in the illustration.
Be careful not to damage the roof headlining when removing it.
41.REMOVE FRONT SIDE RAIL SPACER LH
Detach the 2 claws and remove the front side rail spacer.
42.REMOVE FRONT SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
43.REMOVE SIDE RAIL SPACER
Detach the 2 claws and remove the side rail spacer.
44.REMOVE REAR NO. 2 SIDE RAIL SPACER LH
Use the same procedure for both rear No. 2 side rail spacers.
Detach the 2 claws and remove the rear No. 2 side rail spacer.
45.REMOVE REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
46.REMOVE REAR NO. 3 SIDE RAIL SPACER LH
Detach the 3 claws and remove the rear No. 3 side rail spacer.
47.REMOVE REAR NO. 3 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.