Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052787 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply Primer G to the glass where the stoppers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install 2 new No. 2 windshield glass stoppers to the glass as shown in the illustration.

B282353
1.542,1.25 1.813,0.333 1.813,0.333 2.052,0.333 false 1.458,1.302 1.26,0.479 1.26,0.479 1.073,0.479 false 5.635,1.25 5.354,0.333 5.354,0.333 5.125,0.333 false 5.698,1.302 5.896,0.479 5.896,0.479 6.073,0.479 false 0.094,0.073 0.323,0.281 0.229,0.208 10 false *a 0.865,0.375 1.042,0.583 0.177,0.208 10 false *1 6.115,0.365 6.292,0.573 0.177,0.208 10 false *1 4.927,0.229 5.104,0.438 0.177,0.208 10 false *2 2.104,0.24 2.281,0.448 0.177,0.208 10 false *2 1.188,1.823 1.396,2 0.208,0.177 10 false b 5.896,1.813 6.104,1.99 0.208,0.177 10 false b 2.125,1.177 2.24,1.333 0.115,0.156 10 false a 4.958,1.208 5.125,1.396 0.167,0.188 10 false a
*1 Ceramic Notch *2 Windshield Glass
*a Backside - -


Specification:
Area Measurement
a 7.7 mm (0.303 in.)
b 40.0 mm (1.58 in.)



Hide 2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

a.
B342504
1.573,0.594 1.573,0.427 1.573,0.427 2.25,0.427 false 0.302,1.208 0.302,0.938 0.302,0.938 0.51,0.938 false 1.49,0.625 1.802,0.823 0.313,0.198 10 false *1 0.219,1.24 0.531,1.438 0.313,0.198 10 false *2
*1 Vehicle Body
*2 Stopper


Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.


Hide 3.INSTALL NO. 2 WINDOW GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the glass adhesive dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from a new No. 2 window glass adhesive part of the dam. Install the No. 2 window glass adhesive dam (adhesive side) to the glass (Primer G area), but exclude the spacer area as shown in the illustration.

B282354
5.417,0.667 5.49,0.427 5.49,0.427 5.625,0.427 true 4.208,0.656 4.135,0.417 4.135,0.417 4,0.417 true 4.969,2.229 5.073,2.438 5.073,2.438 5.208,2.438 true 0.729,0.615 0.885,0.802 0.156,0.188 10 false A 2.031,0.615 2.198,0.802 0.167,0.188 10 false B 1.167,1.063 1.333,1.25 0.167,0.188 10 false C 1.167,0.698 1.333,0.885 0.167,0.188 10 false C 2.667,0.292 2.844,0.479 0.177,0.188 10 false A 4.104,1.552 4.583,1.823 0.479,0.271 10 false C - C 4.979,0.302 5.177,0.469 0.198,0.167 10 false B 5.646,0.323 5.854,0.563 0.208,0.24 10 false *1 5.25,2.333 5.5,2.531 0.25,0.198 10 false *2 0.083,0.073 0.292,0.313 0.208,0.24 10 false *a 5.021,1.625 5.24,1.802 0.219,0.177 10 false a 3.854,0.323 4.063,0.563 0.208,0.24 10 false *1
*1 Ceramic Notch *2 Dam Reference Line
*a Backside - -


Specification:
Area Measurement
a 7.0 mm (0.276 in.)



Hide 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the glass adhesive dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from the adhesive part of a new window glass adhesive dam. Install the window glass adhesive dam (adhesive side) to the glass (Primer G area), but exclude the spacer area as shown in the illustration.

B251146
0.865,2.104 0.865,2.344 true 3.146,0.708 3.198,0.427 3.198,0.427 3.323,0.427 true 6.448,0.708 6.385,0.448 6.385,0.448 6.271,0.448 true 3.594,2.208 3.667,2.427 3.667,2.427 3.729,2.427 true 6,2.198 5.833,1.885 5.833,1.885 5.656,1.885 false 0.698,0.563 0.854,0.75 0.156,0.188 10 false A 2.01,0.573 2.177,0.76 0.167,0.188 10 false B 2.729,1.573 2.896,1.76 0.167,0.188 10 false C 2.385,1.667 2.552,1.854 0.167,0.188 10 false C 0.198,1.073 0.344,1.229 0.146,0.156 10 false C 0.542,1.167 0.708,1.344 0.167,0.177 10 false C 1.135,1.875 1.302,2.021 0.167,0.146 10 false D 1.135,2.24 1.406,2.49 0.271,0.25 10 false D 2.719,0.333 3.01,0.604 0.292,0.271 10 false A 4.896,0.344 5.188,0.615 0.292,0.271 10 false B 3.083,1.531 3.625,1.74 0.542,0.208 10 false C - C 5.177,1.531 5.656,1.719 0.479,0.188 10 false D - D 3.365,0.333 3.625,0.5 0.26,0.167 10 false *1 6.125,0.344 6.385,0.51 0.26,0.167 10 false *1 3.771,2.344 4.031,2.51 0.26,0.167 10 false *2 5.479,1.781 5.74,1.948 0.26,0.167 10 false *2 3.917,1.688 4.073,1.865 0.156,0.177 10 false a 0.792,2.354 1.052,2.521 0.26,0.167 10 false *2 0.104,0.073 0.375,0.281 0.271,0.208 10 false *a
*1 Ceramic Notch *2 Dam Reference Line
*a Backside - -


Specification:
Area Measurement
a 7.0 mm (0.276 in.)



Hide 5.INSTALL WINDSHIELD GLASS

B106104
1.802,0.479 2.135,0.24 2.135,0.24 1.792,0.781 true 2.146,0.083 2.427,0.271 0.281,0.188 10 false *1
*1 Matchmark


a.

Position the windshield glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new glass. If it the glass is being reused, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the glass.



b.
B106085
2.302,2.281 1.896,2.281 false 2.417,1.115 1.917,0.771 false 2.365,2.188 1.865,1.844 false 2.156,0.24 2.323,0.396 0.167,0.156 10 false *a 1.708,0.667 1.896,0.813 0.188,0.146 10 false *1 1.656,1.74 1.844,1.885 0.188,0.146 10 false *1 0.552,4.385 0.74,4.531 0.188,0.146 10 false *1 1.656,2.198 1.844,2.344 0.188,0.146 10 false *2 2.25,2.406 2.438,2.552 0.188,0.146 10 false *b
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B282355
2.979,0.646 4.208,2.073 1.229,1.427 4.25,0.646 5.594,2.073 1.344,1.427 5.667,0.646 7.01,2.073 1.344,1.427 2.24,2.021 2.24,2.438 true 3.188,1.344 3.188,1.698 true 4.479,1.344 4.479,1.698 true 6.24,1.344 6.344,1.656 6.344,1.656 6.448,1.344 true 0.083,0.073 0.302,0.333 0.219,0.26 10 false *a 1.063,0.573 1.229,0.771 0.167,0.198 10 false A 2.365,0.563 2.531,0.76 0.167,0.198 10 false A 2.365,0.906 2.531,1.104 0.167,0.198 10 false A 1.052,0.917 1.219,1.115 0.167,0.198 10 false A 1.708,0.542 1.958,0.76 0.25,0.219 10 false B 1.708,0.938 1.958,1.156 0.25,0.219 10 false B 2.458,1.625 2.708,1.844 0.25,0.219 10 false B 2.823,1.542 3.073,1.76 0.25,0.219 10 false B 0.146,1.052 0.396,1.271 0.25,0.219 10 false B 0.677,1.198 0.927,1.417 0.25,0.219 10 false B 1.729,1.75 1.979,1.99 0.25,0.24 10 false C 1.708,2.177 1.958,2.417 0.25,0.24 10 false C 3.031,0.667 3.427,0.875 0.396,0.208 10 false A - A 4.313,0.667 4.708,0.875 0.396,0.208 10 false B - B 5.708,0.667 6.104,0.875 0.396,0.208 10 false C - C 2.146,2.5 2.323,2.646 0.177,0.146 10 false *1 0.573,2.469 0.844,2.615 0.271,0.146 10 false *2 3.104,1.719 3.281,1.865 0.177,0.146 10 false *1 6.26,1.688 6.438,1.833 0.177,0.146 10 false *1 4.396,1.729 4.573,1.875 0.177,0.146 10 false *1
*1 Adhesive Center Line *2 Primer G
*a Backside - -


HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

B282356
4.344,0.042 5.677,1.396 1.333,1.354 5.76,0.042 7.104,1.396 1.344,1.354 4.885,1.448 6.365,2.719 1.479,1.271 4.729,0.938 4.729,1.104 true 6.198,0.938 6.198,1.125 true 5.521,2.115 5.625,2.333 5.625,2.333 5.729,2.115 true 1.938,1.719 1.938,1.958 false 0.094,0.042 0.302,0.24 0.208,0.198 10 false *a 2.375,0.271 2.573,0.51 0.198,0.24 10 false A 3.667,0.26 3.865,0.5 0.198,0.24 10 false A 3.667,0.604 3.865,0.844 0.198,0.24 10 false A 2.354,0.625 2.563,0.823 0.208,0.198 10 false A 3.01,0.271 3.229,0.469 0.219,0.198 10 false B 1.479,0.75 1.698,0.948 0.219,0.198 10 false B 1.969,0.865 2.188,1.063 0.219,0.198 10 false B 4.094,1.229 4.313,1.427 0.219,0.198 10 false B 3.75,1.313 3.969,1.51 0.219,0.198 10 false B 3.01,0.625 3.229,0.823 0.219,0.198 10 false B 3,1.385 3.198,1.615 0.198,0.229 10 false C 3,1.885 3.198,2.115 0.198,0.229 10 false C 0.563,1.51 0.75,1.698 0.188,0.188 10 false a 0.156,2.333 0.344,2.521 0.188,0.188 10 false a 0.531,1.948 0.688,2.115 0.156,0.167 10 false b 0.99,1.573 1.146,1.74 0.156,0.167 10 false b 4.656,1.135 4.833,1.323 0.177,0.188 10 false *1 4.385,0.042 4.833,0.208 0.448,0.167 10 false A - A 5.833,0.042 6.219,0.219 0.385,0.177 10 false B - B 4.927,1.469 5.406,1.677 0.479,0.208 10 false C - C 4.656,0.25 4.875,0.396 0.219,0.146 10 false c 6.115,0.24 6.333,0.385 0.219,0.146 10 false c 5.969,1.448 6.146,1.625 0.177,0.177 10 false d 6.115,1.135 6.292,1.323 0.177,0.188 10 false *1 5.563,2.385 5.74,2.573 0.177,0.188 10 false *1 0.958,2.365 1.135,2.552 0.177,0.188 10 false *2 1.854,1.979 2.031,2.167 0.177,0.188 10 false *1
*1 Adhesive Center Line *2 Adhesive
*a Backside - -


Specification:
Area Measurement
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 3.0 mm (0.118 in.)
d 18.3 mm (0.720 in.)




e.
B106104
1.802,0.479 2.135,0.24 2.135,0.24 1.792,0.781 true 2.146,0.083 2.427,0.271 0.281,0.188 10 false *1
*1 Matchmark


Install the windshield glass to the vehicle body.

i.

Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




iii.

Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.



Hide 6.INSTALL OUTER UPPER WINDSHIELD MOULDING

B282357
1.208,0.583 0.708,0.25 0.708,0.25 2.438,0.25 true 2.146,2.573 2.177,2.323 2.177,2.323 2.24,2.323 false 2.281,2.844 2.375,2.938 2.375,2.938 2.427,2.938 false 2.438,2.854 2.708,3.021 0.271,0.167 10 false *3 2.271,2.24 2.479,2.448 0.208,0.208 10 false *2 0.51,0.167 0.698,0.365 0.188,0.198 10 false *1
*1 Mark
*2 Windshield Glass
*3 Ceramic Notch


a.

Using a brush or sponge, apply Primer G to the glass where a new outer upper windshield moulding will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Align the marks on the moulding with the ceramic notches and install a new outer upper windshield moulding before the adhesive dries.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



Hide 7.CHECK FOR LEAKS AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 8.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 15.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Single Cab)

Hide 16.INSTALL MAP LIGHT ASSEMBLY (w/ Map Light)

Hide 23.INSTALL FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 24.INSTALL COWL TOP VENTILATOR LOUVER RH

Hide 25.INSTALL COWL TOP VENTILATOR LOUVER LH

Hide 27.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 28.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH