1.INSTALL REAR NO. 3 SIDE RAIL SPACER LH
Attach the 3 claws to install the rear No. 3 side rail spacer.
2.INSTALL REAR NO. 3 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
3.INSTALL REAR NO. 2 SIDE RAIL SPACER LH
Use the same procedure for both rear No. 2 side rail spacers.
Attach the 2 claws to install the rear No. 2 side rail spacer.
4.INSTALL REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
5.INSTALL SIDE RAIL SPACER
Attach the 2 claws to install the side rail spacer.
6.INSTALL FRONT SIDE RAIL SPACER LH
Attach the 2 claws to install the front side rail spacer.
7.INSTALL FRONT SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
8.INSTALL ROOF HEADLINING ASSEMBLY
Place the roof headlining into the vehicle as shown in the illustration.
Be careful not to damage the roof headlining when placing it.
Install the roof headlining with the 5 clips.
Connect the connectors and attach the 4 clamps.
Attach the 5 clamps to the front pillar LH.
9.INSTALL BACK WINDOW GLASS
10.INSTALL DEFROSTER NOZZLE ASSEMBLY
11.INSTALL NO. 3 HEATER TO REGISTER DUCT
12.INSTALL NO. 1 HEATER TO REGISTER DUCT
13.INSTALL NO. 2 HEATER TO REGISTER DUCT
14.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
15.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
16.INSTALL ASSIST GRIP
Use the same procedure for all assist grips.
Install the assist grip with the 2 screws.
Attach the 4 claws to close the 2 covers.
17.INSTALL VISOR HOLDER LH
Attach the 2 claws to install the visor holder.
Install the screw.
18.INSTALL VISOR HOLDER RH
Use the same procedure described for the LH side.
19.INSTALL VISOR ASSEMBLY LH
Install the visor with the 2 screws.
Attach the guide.
20.INSTALL VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
21.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
22.INSTALL MAP LIGHT ASSEMBLY
23.INSTALL QUARTER INSIDE TRIM BOARD LH
Attach the 4 clips to install the quarter inside trim board.
Connect the front seat belt shoulder anchor with the bolt.
Attach the 2 claws to close the front seat belt shoulder anchor cover.
24.INSTALL QUARTER INSIDE TRIM BOARD RH
Use the same procedure described for the LH side.
25.INSTALL LOWER QUARTER TRIM PANEL LH
Attach the 3 clips and claw to install the lower quarter trim panel.
26.INSTALL LOWER QUARTER TRIM PANEL RH
Use the same procedure described for the LH side.
27.INSTALL UPPER BACK PANEL GARNISH
Attach the 5 clips and 4 claws to install the upper back panel garnish.
28.INSTALL CENTER PILLAR GARNISH LH
Attach the guide and clip to install the center pillar garnish.
Connect the front seat belt shoulder anchor with the bolt.
Attach the 4 claws to install the front seat belt shoulder anchor cover.
29.INSTALL CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
30.INSTALL LOWER CENTER PILLAR GARNISH LH
Attach the 2 clips, 2 claws and 2 guides to install the lower center pillar garnish.
Connect the front seat outer belt floor anchor with the bolt.
31.INSTALL LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
32.INSTALL REAR DOOR OPENING TRIM LH
| *1 | Paint Mark |
| *2 | Mark Position |
Align the paint mark on the rear door opening trim with the mark position on the vehicle and install the rear door opening trim as shown in the illustration.
33.INSTALL REAR DOOR OPENING TRIM RH
Use the same procedure described for the LH side.
34.INSTALL REAR DOOR SCUFF PLATE LH
Attach the 2 clips and 7 claws to install the rear door scuff plate.
35.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
36.INSTALL FRONT PILLAR GARNISH LH
Attach the 2 guides and 2 clips to install the front pillar garnish.
37.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
38.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for both front assist grips.
Install the front assist grip with the 2 screws.
39.INSTALL ASSIST GRIP PLUG LH
Use the same procedure for both front No. 1 assist grip plug.
Attach the 2 claws to install the front No. 1 assist grip plug.
40.INSTALL ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
41.INSTALL FRONT DOOR OPENING TRIM LH
| *1 | Paint Mark |
| *2 | Mark Position |
Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.
42.INSTALL FRONT DOOR OPENING TRIM RH
Use the same procedure described for the LH side.
43.INSTALL FRONT DOOR SCUFF PLATE LH
Attach the 3 clips and 7 claws to install the front door scuff plate.
44.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
45.INSTALL REAR SEAT ASSEMBLY
46.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
47.CHECK SRS WARNING LIGHT (w/ Airbag System)