1.REMOVE FRONT WIPER ARM HEAD CAP
2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
4.REMOVE HOOD TO COWL TOP SEAL
5.REMOVE COWL TOP VENTILATOR LOUVER LH
6.REMOVE COWL TOP VENTILATOR LOUVER RH
7.REMOVE FRONT DOOR OPENING TRIM LH
Partially remove the front door opening trim LH so that the front pillar garnish LH can be removed (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL).
8.REMOVE FRONT DOOR OPENING TRIM RH
Use the same procedure described for the LH side.
9.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)
10.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)
11.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
12.REMOVE FRONT PILLAR GARNISH LH
13.REMOVE FRONT PILLAR GARNISH RH
14.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Single Cab)
15.REMOVE MAP LIGHT ASSEMBLY (w/ Map Light)
16.REMOVE VISOR ASSEMBLY LH
17.REMOVE VISOR ASSEMBLY RH
18.REMOVE VISOR HOLDER LH
19.REMOVE VISOR HOLDER RH
20.REMOVE ASSIST GRIP
21.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
22.REMOVE ROOF HEADLINING ASSEMBLY
Partially remove the roof headlining.
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL).
23.REMOVE OUTER UPPER WINDSHIELD MOULDING
| *1 | Outer Upper Windshield Moulding |
| *a | Cut |
Using a knife, cut off the outer upper windshield moulding as shown in the illustration.
Be careful not to damage the vehicle body.
Remove the remaining moulding.
Make a partial cut in the moulding. Then pull and remove the moulding by hand.
24.REMOVE WINDSHIELD GLASS
| *1 | Plastic Sheet |
| *2 | Protective Tape |
| *3 | Stopper |
| *4 | Piano Wire |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.
| *1 | Matchmark |
Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.
Matchmarks do not need to be placed if not reusing the glass.
Cut through the adhesive by pulling the piano wire around the glass.
Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
Using suction cups, remove the glass.
25.CLEAN WINDSHIELD GLASS
Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
Clean the outer edges of the glass with non-residue solvent.
Even if using new glass, clean it with non-residue solvent.
26.CLEAN VEHICLE BODY
| *1 | Adhesive |
| *2 | Vehicle Body |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.