Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2012.04–2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052787 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 5.REMOVE COWL TOP VENTILATOR LOUVER LH

Hide 6.REMOVE COWL TOP VENTILATOR LOUVER RH

Hide 7.REMOVE FRONT DOOR OPENING TRIM LH

a.

Partially remove the front door opening trim LH so that the front pillar garnish LH can be removed (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL).


Hide 8.REMOVE FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 9.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)

Hide 10.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)

Hide 11.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

Hide 14.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Single Cab)

Hide 15.REMOVE MAP LIGHT ASSEMBLY (w/ Map Light)

Hide 21.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 22.REMOVE ROOF HEADLINING ASSEMBLY

a.

Partially remove the roof headlining.

i.

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL).



Hide 23.REMOVE OUTER UPPER WINDSHIELD MOULDING

a.

Using a knife, cut off the outer upper windshield moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.
B050448
1.823,0.781 2,0.219 2,0.219 2.104,0.219 false 1.563,0.115 1.813,0.313 0.25,0.198 10 false *a 2.667,0.917 2.917,1.115 0.25,0.198 10 false *a 2.156,0.125 2.344,0.323 0.188,0.198 10 false *1
*1 Outer Upper Windshield Moulding
*a Cut


Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove the moulding by hand.



Hide 24.REMOVE WINDSHIELD GLASS

a.
B282352
2.323,0.469 2.146,0.469 2.146,0.469 2.146,0.802 false 1.135,1.135 0.74,1.135 0.74,1.135 0.74,1.594 true 0.927,2.74 0.927,3.063 0.927,3.063 2.552,3.063 false 2.552,3.063 2.552,2.74 false 1.75,3.063 1.75,3.208 false 0.875,3.823 1.167,3.823 false 2.354,0.365 2.552,0.552 0.198,0.188 10 false *1 0.667,1.604 0.865,1.792 0.198,0.188 10 false *2 1.208,3.719 1.406,3.906 0.198,0.188 10 false *4 1.677,3.229 1.875,3.417 0.198,0.188 10 false *3
*1 Plastic Sheet
*2 Protective Tape
*3 Stopper
*4 Piano Wire


Apply protective tape to the outer surface of the vehicle body to prevent scratches.


b.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


c.

Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




d.
B106095
1.646,1.521 1.094,1.771 1.094,1.771 1.646,1.25 true 0.927,1.698 1.208,1.896 0.281,0.198 10 false *1
*1 Matchmark


Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if not reusing the glass.



e.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



f.

Using suction cups, remove the glass.


Hide 25.CLEAN WINDSHIELD GLASS

B106080

a.

Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.


b.

Clean the outer edges of the glass with non-residue solvent.

NOTICE:
Do not touch the glass surface after cleaning it.

Even if using new glass, clean it with non-residue solvent.



Hide 26.CLEAN VEHICLE BODY

B106081
0.5,1.292 0.688,0.76 0.688,0.76 0.865,0.76 true 2.26,1.438 2.542,0.74 2.542,0.74 2.708,0.74 true 2.427,1.604 2.427,1.781 false 0.813,1.573 0.813,1.76 false 0.896,0.667 1.135,0.865 0.24,0.198 10 false *1 2.75,0.656 2.99,0.854 0.24,0.198 10 false *1 0.729,1.781 0.969,1.979 0.24,0.198 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2
*1 Adhesive
*2 Vehicle Body


a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.