Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS(for Extra Cab) › from 2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052793 BACK WINDOW GLASS(for Extra Cab) A

WINDOW / GLASS  BACK WINDOW GLASS(for Extra Cab)  REMOVAL  


PROCEDURE

Hide 3.REMOVE REAR SEATBACK ASSEMBLY

Hide 4.REMOVE FRONT DOOR OPENING TRIM LH

a.

Partially remove the front door opening trim LH so that the inside trim board LH and inner upper roof side garnish LH can be removed (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Extra Cab)>REMOVAL).


Hide 5.REMOVE FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 13.REMOVE ROOF HEADLINING ASSEMBLY

a.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the back window glass can be removed in a later step (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Extra Cab)>REMOVAL).



Hide 14.REMOVE BACK WINDOW GLASS

a.
B282422
1.406,0.823 1.406,0.313 1.406,0.313 1.625,0.313 false 1.365,3.927 1.365,4.313 1.365,4.313 1.667,4.313 false 0.26,3.771 0.531,3.427 0.531,3.427 1.573,3.427 false 3.188,3.781 2.917,3.427 2.917,3.427 1.833,3.427 false 0.896,3.156 1.135,2.531 1.135,2.531 1.542,2.531 false 2.573,3.156 2.323,2.531 2.323,2.531 1.833,2.531 false 1.688,0.229 1.844,0.417 0.156,0.188 10 false *1 1.646,3.333 1.865,3.521 0.219,0.188 10 false *3 1.635,2.417 1.875,2.604 0.24,0.188 10 false *2 1.708,4.198 1.906,4.417 0.198,0.219 10 false *4
*1 Protective Tape
*2 Stopper
*3 Spacer
*4 Piano Wire


Apply protective tape to the outer surface of the vehicle body to prevent scratches.


b.

From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.


c.

Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

NOTICE:

When separating the back window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.



d.

Cut through the adhesive by pulling the piano wire around the back window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



e.

Using suction cups, remove the back window glass.


Hide 15.CLEAN BACK WINDOW GLASS

a.
B106929

Using a scraper, remove the spacers, moulding and adhesive sticking to the back window glass.


b.

Clean the outer edges of the back window glass with non-residue solvent.

NOTICE:
·

Do not touch the back window glass surface after cleaning it.

·

Even if using new back window glass, clean it with non-residue solvent.




Hide 16.CLEAN VEHICLE BODY

a.
B106081
0.469,1.313 0.708,0.792 0.708,0.792 0.885,0.792 true 2.24,1.469 2.521,0.771 2.521,0.771 2.688,0.771 true 2.427,1.615 2.427,1.792 false 0.813,1.573 0.813,1.76 false 0.906,0.688 1.146,0.885 0.24,0.198 10 false *1 2.708,0.667 2.948,0.865 0.24,0.198 10 false *1 0.719,1.792 0.958,1.99 0.24,0.198 10 false *2 2.323,1.813 2.563,2.01 0.24,0.198 10 false *2
*1 Adhesive
*2 Vehicle Body


Clean and shape the contact surface of the vehicle body.

i.

Use a knife to cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with cleaner.

NOTICE:

Even if all the adhesive has been removed, clean the vehicle body.