Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0156  Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  P0158  Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)  


DESCRIPTION

A three-way catalytic converter is used in order to convert the carbon monoxide, hydrocarbons, and nitrogen oxide into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the three-way catalytic converter, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-three-way catalytic converter air fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three-way catalytic converter air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the three-way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A115539
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 true 2.594,2.417 3.25,2.385 true 2.677,2.698 3.26,2.833 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.729,1.646 3.302,1.271 3.302,1.271 2.667,1.49 true 1.448,0.771 2.458,0.969 1.01,0.198 10 false Atmospheric Air 3.313,0.74 4.052,0.938 0.74,0.198 10 false Housing 3.323,1.188 4.854,1.385 1.531,0.198 10 false Platinum Electrode 3.958,0.885 4.927,1.083 0.969,0.198 10 false Output Voltage 5.01,0.927 6.396,1.125 1.385,0.198 10 false Ideal Air-fuel Mixture 2.01,3.167 2.906,3.365 0.896,0.198 10 false Exhaust Gas 3.344,1.698 4.802,2.063 1.458,0.365 10 false Solid Electrolyte (Zirconia Element) 3.292,2.76 4.49,2.958 1.198,0.198 10 false Coating (Ceramic) 3.323,2.281 3.802,2.479 0.479,0.198 10 false Heater 1.375,2.844 1.813,3.052 0.438,0.208 10 false Cover 4.792,2.938 7.094,3.135 2.302,0.198 10 false Richer - Air-fuel Ratio - Leaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Abnormal voltage output:

During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage does not decrease to below 0.21 V.

2.

The heated oxygen sensor voltage does not increase to higher than 0.59 V.



·

Open or short in heated oxygen sensor (for bank 1 sensor 2) circuit

·

Heated oxygen sensor (for bank 1 sensor 2)

·

Heated oxygen sensor heater (for bank 1 sensor 2)

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)

Low voltage (open):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage output is below 0.21 V.

2.

The target air fuel ratio is rich.



·

Open in heated oxygen sensor (for bank 1 sensor 2) circuit

·

Heated oxygen sensor (for bank 1 sensor 2)

·

Heated oxygen sensor heater (for bank 1 sensor 2)

·

Gas leak from exhaust system


Comes on DTC stored
P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)

High voltage (short):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) The heated oxygen sensor voltage output is higher than 0.59 V.


(b) The target air fuel ratio is lean.



·

Short in heated oxygen sensor (for bank 1 sensor 2) circuit

·

Heated oxygen sensor (for bank 1 sensor 2)

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

ECM


Comes on DTC stored
P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)

Abnormal voltage output:

During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage does not decrease to below 0.21 V.

2.

The heated oxygen sensor voltage does not increase to higher than 0.59 V.



·

Open or short in heated oxygen sensor (for bank 2 sensor 2) circuit

·

Heated oxygen sensor (for bank 2 sensor 2)

·

Heated oxygen sensor heater (for bank 2 sensor 2)

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored
P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)

Low voltage (open):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage output is below 0.21 V.

2.

The target air fuel ratio is rich.



·

Open in heated oxygen sensor (for bank 2 sensor 2) circuit

·

Heated oxygen sensor (for bank 2 sensor 2)

·

Heated oxygen sensor heater (for bank 2 sensor 2)

·

Gas leak from exhaust system


Comes on DTC stored
P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)

High voltage (short):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) The heated oxygen sensor voltage output is higher than 0.59 V.


(b) The target air fuel ratio is lean.



·

Short in heated oxygen sensor (for bank 2 sensor 2) circuit

·

Heated oxygen sensor (for bank 2 sensor 2)

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

Active Air-Fuel Ratio Control

The ECM usually performs air-fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air-fuel ratio. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the three-way catalytic converter and heated oxygen sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of HO2 Sensor (DTC P0136 and P0156)

While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not decrease to below 0.21 V and does not increase to higher than 0.59 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.

A115540
3.281,1.635 3.073,1.354 false 3.313,1.844 3.167,2.135 false 0.094,0.135 3.583,0.344 3.49,0.208 10 false HEATED OXYGEN SENSOR CIRCUIT MALFUNCTION 0.208,0.865 2.021,1.052 1.813,0.188 10 false Active Air-fuel Ratio Control 0.219,2.073 2.198,2.313 1.979,0.24 10 false Heated Oxygen Sensor Voltage 2.448,0.854 2.698,1.052 0.25,0.198 10 false Off 2.594,1.26 3.083,1.458 0.49,0.198 10 false Normal 2.229,1.656 2.729,1.854 0.5,0.198 10 false 0.59 V 2.219,2.406 2.729,2.604 0.51,0.198 10 false 0.21 V 2.563,2.094 3.26,2.292 0.698,0.198 10 false Abnormal 4.625,0.156 5.792,0.354 1.167,0.198 10 false 15 to 20 seconds 4.219,0.823 4.896,1.021 0.677,0.198 10 false Operating 0.094,0.531 2.875,0.708 2.781,0.177 10 false (P0136 and P0156: ABNORMAL VOLTAGE)


Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157 or P0138 and P0158)

During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the three-way catalytic converter by forcibly regulating the air-fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the heated oxygen sensor voltage output is below 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157. When the target air-fuel ratio is lean and the voltage output is higher than 0.59 V (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high, and stores DTC P0138 or P0158.

HINT:

The three-way catalytic converter has the capability to store oxygen. The OSC and the emission purification capacity of the three-way catalytic converter are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.


A115541
4.667,2.063 4.385,1.917 false 5.979,6.24 6.167,6.021 false 5.948,2.719 6.135,2.385 false 6,3.5 6.188,3.708 false 5.198,2.417 5.313,1.885 false 0.073,0.104 3.229,0.333 3.156,0.229 10 false HO2 SENSOR CIRCUIT LOW VOLTAGE 0.083,0.49 1.854,0.698 1.771,0.208 10 false (P0137 and P0157: OPEN) 1.167,1.594 3.125,1.792 1.958,0.198 10 false Active air-fuel ratio control 1.167,3 2.656,3.198 1.49,0.198 10 false HO2 sensor voltage 1.167,2.135 2.635,2.333 1.469,0.198 10 false Target air-fuel ratio 2.563,2.063 3.469,2.406 0.906,0.344 10 false Stoichiometric Air-Fuel Ratio 3.24,1.76 3.5,1.958 0.26,0.198 10 false Off 3.01,3.167 3.469,3.365 0.458,0.198 10 false 0.21 V 0.115,4.104 3.281,4.313 3.167,0.208 10 false HO2 SENSOR CIRCUIT HIGH VOLTAGE 0.073,4.552 1.917,4.76 1.844,0.208 10 false (P0138 and P0158: SHORT) 1.188,5.167 3.146,5.365 1.958,0.198 10 false Active air-fuel ratio control 1.188,6.521 2.677,6.719 1.49,0.198 10 false HO2 sensor voltage 1.188,5.802 2.656,6 1.469,0.198 10 false Target air-fuel ratio 2.573,5.719 3.49,6.094 0.917,0.375 10 false Stoichiometric Air-Fuel Ratio 3.229,5.24 3.49,5.438 0.26,0.198 10 false Off 3.021,6.458 3.563,6.656 0.542,0.198 10 false 0.59 V 4.615,0.594 5.917,0.792 1.302,0.198 10 false 15 to 20 seconds 4.51,1.667 5.271,1.865 0.76,0.198 10 false Operating 4.531,4.719 5.292,4.917 0.76,0.198 10 false Operating 4.531,5.302 4.927,5.5 0.396,0.198 10 false Lean 3.938,1.844 4.5,2.042 0.563,0.198 10 false Normal 6.219,5.948 6.958,6.146 0.74,0.198 10 false Abnormal 5.281,1.698 6.021,1.896 0.74,0.198 10 false Abnormal 6.219,3.615 6.958,3.813 0.74,0.198 10 false Abnormal 6.188,2.281 6.75,2.479 0.563,0.198 10 false Normal 4.771,2.438 5.135,2.635 0.365,0.198 10 false Rich


During normal air-fuel ratio feedback control, there are small variations in the exhaust gas oxygen concentration. In order to continuously monitor the slight variations in the heated oxygen sensor signal while the engine is running, the impedance* of the sensor is measured by the ECM. The ECM determines that there is a malfunction in the sensor when the measured impedance deviates from the standard range.

*: The effective resistance in an alternating current electrical circuit.

HINT:
·

The impedance cannot be measured using an ohmmeter.

·

DTC P0136 and P0156 indicate the deterioration of the heated oxygen sensor. The ECM stores this DTC by calculating the impedance of the sensor when the typical enabling conditions are satisfied (2 driving cycles).

·

DTC P0137 and P0157 indicate an open or short circuit in the heated oxygen sensor (2 driving cycles). The ECM stores this DTC when the impedance of the sensor exceeds the threshold of 15 kΩ.




WIRING DIAGRAM

A279106
0.552,5.313 1.052,5.542 0.5,0.229 10 false Battery 0.438,3.26 0.833,3.448 0.396,0.188 10 false BATT 0.521,0.417 0.646,0.583 0.125,0.167 10 false 1 0.469,0.625 0.698,0.792 0.229,0.167 10 false 1H 2.354,0.417 2.479,0.583 0.125,0.167 10 false 5 0.854,1.49 0.979,1.656 0.125,0.167 10 false 3 2.302,0.635 2.531,0.802 0.229,0.167 10 false 1J 2.333,0.865 2.458,1.031 0.125,0.167 10 false 2 2.292,1.073 2.521,1.24 0.229,0.167 10 false 1J 1.052,1.49 1.281,1.656 0.229,0.167 10 false 1J 0.969,0.75 1.24,0.917 0.271,0.167 10 false EFI 1.635,1.375 2.115,1.542 0.479,0.167 10 false MAIN 1.198,1.698 2.708,1.938 1.51,0.24 10 false No. 1 Integration Relay 3.698,0.521 3.813,0.688 0.115,0.167 10 false 2 3.688,1.292 3.802,1.458 0.115,0.167 10 false 4 4.708,0.5 4.823,0.667 0.115,0.167 10 false 1 4.708,1.281 4.823,1.448 0.115,0.167 10 false 3 3.875,0.521 4.104,0.688 0.229,0.167 10 false +B 3.875,1.281 4.094,1.458 0.219,0.177 10 false E2 4.292,0.521 4.667,0.677 0.375,0.156 10 false HT1B 4.271,1.208 4.688,1.375 0.417,0.167 10 false OX1B 3.729,3.156 3.844,3.323 0.115,0.167 10 false 2 3.729,3.927 3.844,4.094 0.115,0.167 10 false 4 4.75,3.156 4.865,3.323 0.115,0.167 10 false 1 4.75,3.927 4.865,4.094 0.115,0.167 10 false 3 3.917,3.146 4.146,3.313 0.229,0.167 10 false +B 3.906,3.927 4.125,4.104 0.219,0.177 10 false E2 4.302,3.135 4.677,3.292 0.375,0.156 10 false HT2B 4.281,3.865 4.698,4.031 0.417,0.167 10 false OX2B 3.521,1.75 3.813,1.917 0.292,0.167 10 false C88 3.521,1.896 4.99,2.281 1.469,0.385 10 false Heated Oxygen Sensor (for Bank 1 Sensor 2) 3.563,4.375 3.948,4.542 0.385,0.167 10 false C152 3.563,4.531 5.042,4.917 1.479,0.385 10 false Heated Oxygen Sensor (for Bank 2 Sensor 2) 6.313,6 6.667,6.188 0.354,0.188 10 false ECM 5.771,0.417 5.896,0.594 0.125,0.177 10 false 1 6.073,0.51 6.479,0.677 0.406,0.167 10 false HT1B 5.656,0.625 6.073,0.802 0.417,0.177 10 false C129 5.74,1.198 5.958,1.375 0.219,0.177 10 false 18 6.083,1.427 6.49,1.594 0.406,0.167 10 false OX1B 5.656,1.406 6.052,1.583 0.396,0.177 10 false C129 5.771,3.063 5.917,3.24 0.146,0.177 10 false 5 6.073,3.156 6.479,3.323 0.406,0.167 10 false HT2B 5.646,3.281 6.094,3.458 0.448,0.177 10 false C130 5.729,3.854 5.958,4.031 0.229,0.177 10 false 33 6.063,4.063 6.469,4.229 0.406,0.167 10 false OX2B 5.646,4.052 6.021,4.229 0.375,0.177 10 false C130 5.74,5.031 5.979,5.208 0.24,0.177 10 false 28 6.073,5.229 6.313,5.396 0.24,0.167 10 false E2 5.667,5.229 6.031,5.406 0.365,0.177 10 false C129 5.771,5.49 5.906,5.667 0.135,0.177 10 false 8 6.063,5.583 6.469,5.75 0.406,0.167 10 false MREL 5.646,5.677 6.021,5.854 0.375,0.177 10 false G155 5.135,3.698 5.24,3.833 0.104,0.135 10 false * 5.24,1.063 5.344,1.198 0.104,0.135 10 false * 1.594,6.177 2.323,6.375 0.729,0.198 10 false *: Shielded 0.438,3.396 0.833,3.583 0.396,0.188 10 false P/I

CONFIRMATION DRIVING PATTERN

A199376
1.99,2.427 2.229,2.604 0.24,0.177 10 [A] 2.594,2.083 2.802,2.271 0.208,0.188 10 [B] 3.958,0.698 4.177,0.885 0.219,0.188 10 [C] 5,3.302 5.219,3.5 0.219,0.198 10 [D] 0.438,0.49 1.656,0.677 1.219,0.188 10 100 km/h (63 mph) 0.469,1.365 1.594,1.552 1.125,0.188 10 60 km/h (37 mph) 1.229,2.188 1.635,2.396 0.406,0.208 10 Idling 0.417,2.385 1.604,2.771 1.188,0.385 10 Ignition Switch ON 2.333,2.896 3.146,3.083 0.813,0.188 10 Warming up 3.5,2.885 4.76,3.104 1.26,0.219 10 10 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the transmission in 5th gear or higher, drive the vehicle at a speed between 60 and 100 km/h (37 and 63 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [D].




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

5.

Perform the Active Test operation with the engine idling.

6.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.



HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
-12% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
-12% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A301859
0.135,0.688 0.75,0.885 0.615,0.198 10 false Case 0.844,0.635 2.906,1.021 2.063,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.427,0.625 5.573,1 2.146,0.375 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 6.042,0.688 7.01,0.938 0.969,0.25 10 false Trouble Area 6.427,2.208 6.719,2.479 0.292,0.271 10 false - 0.24,2.198 0.448,2.458 0.208,0.26 10 false 1 0.26,4.292 0.469,4.552 0.208,0.26 10 false 2 0.26,6.344 0.469,6.604 0.208,0.26 10 false 3 0.26,8.396 0.469,8.656 0.208,0.26 10 false 4 1.438,1.594 2.052,1.792 0.615,0.198 8 false +12% 1.479,1.823 2.094,2.021 0.615,0.198 8 false -12% 0.594,2.167 1.646,2.396 1.052,0.229 9 false Output Voltage 0.594,1.302 1.688,1.542 1.094,0.24 9 false Injection Volume 0.906,2.625 1.917,2.802 1.01,0.177 8 false Higher than 3.4 V 1.156,2.875 1.948,3.115 0.792,0.24 8 false Below 3.1 V 2.521,2.75 2.823,3 0.302,0.25 8 false OK 1.49,3.885 2.104,4.083 0.615,0.198 8 false -12% 1.458,3.656 2.073,3.854 0.615,0.198 8 false +12% 0.583,3.417 1.615,3.771 1.031,0.354 9 false Injection Volume 0.583,4.417 1.781,4.594 1.198,0.177 9 false Output Voltage 0.875,4.802 2,5.042 1.125,0.24 8 false Almost no reaction 2.552,4.719 2.938,5 0.385,0.281 8 false NG 1.573,5.927 2.188,6.125 0.615,0.198 8 false -12% 1.552,5.698 2.167,5.896 0.615,0.198 8 false +12% 0.583,5.5 1.844,5.698 1.26,0.198 9 false Injection Volume 0.583,6.417 1.677,6.688 1.094,0.271 9 false Output Voltage 0.948,6.76 2.073,6.969 1.125,0.208 8 false Higher than 3.4 V 1.198,6.979 1.99,7.219 0.792,0.24 8 false Below 3.1 V 2.531,6.865 2.833,7.115 0.302,0.25 8 false OK 0.583,7.5 1.896,7.781 1.313,0.281 9 false Injection Volume 1.531,8.01 2.146,8.208 0.615,0.198 8 false -12% 1.51,7.823 2.125,8.021 0.615,0.198 8 false +12% 0.583,8.5 1.969,8.771 1.385,0.271 9 false Output Voltage 0.854,8.938 2.052,9.281 1.198,0.344 8 false Almost no reaction 2.563,8.854 2.948,9.135 0.385,0.281 8 false NG 3.323,1.302 4.521,1.51 1.198,0.208 9 false Injection Volume 4.115,1.615 4.729,1.813 0.615,0.198 8 false +12% 4.125,1.813 4.74,2.01 0.615,0.198 8 false -12% 3.344,2.167 4.271,2.375 0.927,0.208 9 false Output Voltage 3.521,2.594 4.552,2.771 1.031,0.177 8 false Higher than 0.55 V 3.844,2.833 4.521,3.073 0.677,0.24 8 false Below 0.4 V 5.188,2.719 5.49,2.969 0.302,0.25 8 false OK 3.25,3.417 4.385,3.646 1.135,0.229 9 false Injection Volume 4.094,3.875 4.708,4.073 0.615,0.198 8 false -12% 4.073,3.656 4.688,3.854 0.615,0.198 8 false +12% 3.25,4.333 4.396,4.552 1.146,0.219 9 false Output Voltage 3.479,4.688 4.563,4.854 1.083,0.167 8 false Higher than 0.55 V 3.802,4.927 4.635,5.167 0.833,0.24 8 false Below 0.4 V 5.208,4.813 5.51,5.063 0.302,0.25 8 false OK 6.01,3.583 6.833,3.917 0.823,0.333 9 false Air fuel ratio sensor 6,4 6.76,4.573 0.76,0.573 8 false Air fuel ratio sensor heater 6,4.417 6.76,5 0.76,0.583 8 false Air fuel ratio sensor circuit 5.885,3.583 6.052,3.771 0.167,0.188 10 false - 5.885,3.979 6.052,4.167 0.167,0.188 10 false - 5.885,4.417 6.052,4.604 0.167,0.188 10 false - 4.125,5.938 4.74,6.135 0.615,0.198 8 false -12% 4.083,5.75 4.698,5.948 0.615,0.198 8 false +12% 3.25,5.5 4.448,5.75 1.198,0.25 9 false Injection Volume 3.25,6.417 4.365,6.635 1.115,0.219 9 false Output Voltage 3.49,6.875 4.646,7.115 1.156,0.24 8 false Almost no reaction 5.177,6.781 5.563,7.063 0.385,0.281 8 false NG 3.25,7.5 4.448,7.875 1.198,0.375 9 false Injection Volume 4.156,8.031 4.771,8.229 0.615,0.198 8 false -12% 4.135,7.833 4.75,8.031 0.615,0.198 8 false +12% 3.49,8.938 4.542,9.208 1.052,0.271 8 false Almost no reaction 5.156,8.854 5.542,9.135 0.385,0.281 8 false NG 3.25,8.5 4.375,8.865 1.125,0.365 9 false Output Voltage 6,5.583 6.833,5.958 0.833,0.375 8 false Heated oxygen sensor 6,6.083 6.833,6.417 0.833,0.333 8 false Heated oxygen sensor heater 6,6.583 6.833,6.917 0.833,0.333 8 false Heated oxygen sensor circuit 5.885,6.063 6.052,6.25 0.167,0.188 10 false - 5.885,5.573 6.052,5.76 0.167,0.188 10 false - 5.885,6.563 6.052,6.75 0.167,0.188 10 false - 6,7.542 6.865,7.917 0.865,0.375 8 false Fuel injector assembly 6.01,7.917 6.583,8.344 0.573,0.427 8 false Fuel pressure 6.01,8.313 6.833,9.417 0.823,1.104 8 false Gas leak from exhaust system (air-fuel ratio extremely rich or lean) 5.875,7.521 6.042,7.708 0.167,0.188 10 false - 5.885,7.896 6.052,8.083 0.167,0.188 10 false - 5.885,8.292 6.052,8.479 0.167,0.188 10 false -

·

Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2; then press the view button.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
P0138 or P0158 is output A
P0137 or P0157 is output B
P0136 or P0156 is output C
P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output D




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

7.CHECK FOR EXHAUST GAS LEAK

C

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)

D

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2 or O2S B2S2.

Powertrain > Engine > Data List
Tester Display
O2S B1S2
O2S B2S2
50003 61 324,330

e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.

Result:
Result Proceed to
1.0 V or higher A
Below 1.0 V B




A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.
A117841
2.052,1.948 2.396,2.25 false 1.385,2.021 1.094,2.344 false 2.021,1.448 2.354,1.083 false 1.385,1.438 1.104,1.094 false 0.927,0.927 1.156,1.104 0.229,0.177 10 +B 0.906,2.333 1.125,2.531 0.219,0.198 10 E2 2.396,0.885 2.948,1.083 0.552,0.198 10 HT1B*A 2.396,1.146 2.979,1.344 0.583,0.198 10 HT2B*B 2.427,2.125 2.99,2.323 0.563,0.198 10 OX1B*A 2.427,2.365 3.021,2.563 0.594,0.198 10 OX2B*B 0.135,0.052 0.365,0.229 0.229,0.177 10 *a
*A for Bank 1 Sensor 2
*B for Bank 2 Sensor 2
*a Component without harness connected
(Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX2B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C129-1 (HT1B) - C129-18 (OX1B) Always 10 kΩ or higher
C130-5 (HT2B) - C130-33 (OX2B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
O2S B1S2
O2S B2S2
50004 61 1 56,58,324,330

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.

HINT:
·

Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within this range.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the tester.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio)
AFS Voltage B2S1 (Air fuel ratio)
Alternates between higher than and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V NG


HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.



A121606
5.885,2.458 6.365,1.396 false 5.542,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.292,1.771 4.094,1.698 false 3.573,2.604 3.188,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.656,0.292 3.208,0.521 0.552,0.229 10 false +12% 4.031,1.135 4.573,1.417 0.542,0.281 10 false -12% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.854,2.615 6.646,2.885 0.792,0.271 10 false Malfunction 4.76,0.125 5.865,0.354 1.104,0.229 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.958,1.813 0.552,0.688 10 false Air Fuel Ratio Sensor Output 4.344,1.729 4.865,1.958 0.521,0.229 10 false Normal


OK

6.CHECK AIR FUEL RATIO SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
6.CHECK AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 3 mA in this test.


a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.

Powertrain > Engine > Clear DTCs
50002 61

e.

Clear DTCs.


f.

Drive the vehicle using the drive pattern as listed below:

i.

Warm up the engine.


ii.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.


iii.

Stop the vehicle.


iv.

Accelerate the vehicle to 60 km/h (37 mph) or more and then decelerate for 5 seconds or more. Repeat this process at least 3 times.

A152792
1.354,2.51 2.635,2.698 1.281,0.188 10 false 10 minutes or more 2.969,2.51 4.177,2.698 1.208,0.188 10 false 5 seconds or more 4.271,2.51 5.469,2.698 1.198,0.188 10 false 5 seconds or more 5.563,2.51 6.74,2.698 1.177,0.188 10 false 5 seconds or more 0.135,0.156 1.438,0.375 1.302,0.219 12 false Driving Pattern: 0.365,1.313 0.958,1.531 0.594,0.219 10 false 60 km/h 0.365,2.042 0.896,2.406 0.531,0.365 10 false 0 km/h 0.354,1.469 0.948,1.646 0.594,0.177 10 false (37 mph) 0.323,2.208 0.948,2.458 0.625,0.25 10 false (0 mph)



g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.

Powertrain > Engine > Data List
Tester Display
AFS Current B1S1
AFS Current B2S1
50003 61 473,475

h.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is performing.

Standard current:

Below 3.6 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.




Result:
Proceed to
OK
NG



OK

10.REPLACE HEATED OXYGEN SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leakage.

OK:

No gas leak.



Result:
Proceed to
OK
NG



OK

8.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

8.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C88-1 (HT1B) - C129-1 (HT1B) Always Below 1 Ω
C88-3 (OX1B) - C129-18 (OX1B) Always Below 1 Ω
C88-4 (E2) - C129-28 (E2) Always Below 1 Ω
C152-1 (HT2B) - C130-5 (HT2B) Always Below 1 Ω
C152-3 (OX2B) - C130-33 (OX2B) Always Below 1 Ω
C152-4 (E2) - C129-28 (E2) Always Below 1 Ω
C88-1 (HT1B) or C129-1 (HT1B) - Body ground Always 10 kΩ or higher
C88-3 (OX1B) or C129-18 (OX1B) - Body ground Always 10 kΩ or higher
C88-4 (E2) or C129-28 (E2) - Body ground Always 10 kΩ or higher
C152-1 (HT2B) or C130-5 (HT2B) - Body ground Always 10 kΩ or higher
C152-3 (OX2B) or C130-33 (OX2B) - Body ground Always 10 kΩ or higher
C152-4 (E2) or C129-28 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

10.REPLACE HEATED OXYGEN SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.PERFORM CONFIRMATION DRIVING PATTERN
11.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

e.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


f.

Check the DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern again by accelerating the vehicle and using the second gear to decelerate the vehicle.


Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(P0136, P0137, P0138, P0156, P0157 or P0158 is output)
B



A

END

B

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume
Data List Display
O2S B1S2
O2S B2S2
50004 61 1 324,330

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the heated oxygen sensors displayed on the tester.

HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations within this range.

·

The heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the tester.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.



Result:
Proceed to
OK
NG



OK

14.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)

NG

7.CHECK FOR EXHAUST GAS LEAK
14.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
O2S B1S2
O2S B2S2
50004 61 1 56,58,324,330

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.

HINT:
·

Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within this range.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the tester.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio)
AFS Voltage B2S1 (Air fuel ratio)
Alternates between higher than and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V NG


HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606
5.813,2.469 6.063,1.531 false 5.5,2.26 6.063,1.521 false 5.656,1.667 6.052,1.531 false 5.563,2.448 5.844,2.667 false 3.01,1.24 2.854,1.656 false 4.396,1.844 4.094,1.677 false 3.583,2.563 3.188,2.906 false 1.958,1.979 2.125,1.979 false 1.958,2.948 2.156,2.948 false 1.542,1.906 1.917,2.063 0.375,0.156 10 false 3.3 V 2.656,0.26 3.083,0.458 0.427,0.198 10 false +12% 4.125,1.125 4.51,1.323 0.385,0.198 10 false -12% 1.656,2.896 1.906,3.094 0.25,0.198 10 false 1 V 1.667,3.396 1.906,3.594 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.875,2.615 6.604,2.792 0.729,0.177 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.646,2.479 5.656,2.688 2.01,0.208 10 false Heated Oxygen Sensor Output 6.073,1.208 7.01,1.615 0.938,0.406 10 false Air Fuel Ratio Sensor Output 4.417,1.792 4.906,1.958 0.49,0.167 10 false Normal



OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR, FUEL PRESSURE, GAS LEAK FROM SYSTEM, ETC.)

NG

15.REPLACE AIR FUEL RATIO SENSOR
15.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

e.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


f.

Check the DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern again by accelerating the vehicle and using the second gear to decelerate the vehicle.


Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(P0136, P0137, P0138, P0156, P0157 or P0158 is output)
B



A

END

B