Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) The ignition switch is ON.
(b) The STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A253407
5.667,1.385 6.01,1.542 0.344,0.156 10 ST1- 5.385,1.375 5.583,1.531 0.198,0.156 10 16 5.646,0.646 5.958,0.802 0.313,0.156 10 STP 5.385,0.625 5.583,0.781 0.198,0.156 10 15 6.073,2.927 6.458,3.094 0.385,0.167 10 G155 6.083,3.073 6.448,3.24 0.365,0.167 10 ECM 4.021,1.396 4.167,1.563 0.146,0.167 10 3 4.875,1.406 5.021,1.573 0.146,0.167 10 4 4.854,0.646 5,0.813 0.146,0.167 10 1 4.031,0.646 4.177,0.813 0.146,0.167 10 2 4.052,1.813 4.396,2 0.344,0.188 10 A24 4.052,1.969 5.156,2.313 1.104,0.344 10 Stop Light Switch Assembly 3.385,0.906 3.781,1.063 0.396,0.156 10 STOP 3.448,1.646 3.719,1.802 0.271,0.156 10 IGN 1.01,0.927 1.292,1.094 0.281,0.167 10 ALT 1,1.667 1.354,1.833 0.354,0.167 10 AM2 1.958,1.375 2.302,1.542 0.344,0.167 10 AM2 2.563,1.375 2.885,1.542 0.323,0.167 10 IG2 1.771,1.375 1.885,1.531 0.115,0.156 10 5 2.917,1.375 3.031,1.531 0.115,0.156 10 6 1.927,2.052 2.823,2.406 0.896,0.354 10 Ignition Switch Assembly 1.927,1.906 2.208,2.063 0.281,0.156 10 G9 0.625,2.417 1.115,2.594 0.49,0.177 10 Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.

Powertrain > Engine > Data List
Tester Display
Stop Light Switch
50003 61 188

e.

Read the value displayed on the tester.

Standard:
Condition Specified Condition
Brake pedal depressed STP signal ON
Brake pedal released STP signal OFF



Result:
Proceed to
OK
NG



OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
A200909
0.615,1.063 0.958,1.323 0.344,0.26 0.104,0.146 0.417,0.344 0.313,0.198 10 *a 0.667,1.115 0.979,1.313 0.313,0.198 10 A24
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V
A24-3 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY, IGNITION SWITCH ASSEMBLY)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (STP AND ST1 - VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK ECM (STP AND ST1 - VOLTAGE)
a.
A112419
2.667,2.469 3.042,2.719 0.375,0.25 2.719,3.427 3.094,4.083 true 2.667,3.417 2.24,4.052 true 0.844,0.146 1.031,0.365 0.188,0.219 10 *a 0.281,2.052 0.469,2.26 0.188,0.208 10 *c 2.479,0.135 2.667,0.344 0.188,0.208 10 *b 2.771,4.094 3.344,4.333 0.573,0.24 10 15 (STP) 1.927,4.094 2.604,4.333 0.677,0.24 10 16 (ST1-) 2.688,2.51 3.156,2.708 0.469,0.198 10 G155
*1 Brake Pedal Depressed
*2 Brake Pedal Released
*a Component with harness connected
(to ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G155-16 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed Below 3.0 V
G155-15 (STP) - Body ground Brake pedal released Below 3.0 V
Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR