Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) The vehicle speed is 20 km/h (12.4 mph) or more.

(b) The engine speed is 1000 rpm or more.

(c) The STA signal is on.


·

Park/neutral position switch assembly

·

Starter signal circuit

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A231469
1.229,1.979 1.74,2.313 0.51,0.333 10 false Idling 0.396,2.25 1.635,2.604 1.24,0.354 10 false Ignition Switch ON 0.438,0.813 1.667,1.125 1.229,0.313 10 false 24 km/h (15 mph) 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.917,3.198 1.323,0.26 10 false 20 seconds or more 2,2.333 2.271,2.583 0.271,0.25 10 false [A] 2.583,2.125 2.885,2.385 0.302,0.26 10 false [B] 4.031,0.458 4.302,0.688 0.271,0.229 10 false [C] 4.906,3.344 5.188,3.594 0.281,0.25 10 false [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A279109
5.698,0.552 6.094,0.729 0.396,0.177 10 false NSW 5.719,2.917 6.094,3.094 0.375,0.177 10 false STA 5.406,0.573 5.521,0.729 0.115,0.156 10 false 8 5.365,2.844 5.552,3 0.188,0.156 10 false 11 6.073,4.219 6.417,4.385 0.344,0.167 10 false ECM 3.667,1.563 3.792,1.719 0.125,0.156 10 false L 4.188,1.573 4.313,1.729 0.125,0.156 10 false B 3.49,1.563 3.615,1.719 0.125,0.156 10 false 5 4.385,1.573 4.51,1.729 0.125,0.156 10 false 4 3.219,1.938 3.573,2.094 0.354,0.156 10 false C26 3.198,2.094 5,2.542 1.802,0.448 10 false Park/Neutral Position Switch Assembly 2.396,0.885 2.625,1.031 0.229,0.146 10 false ST 0.729,0.677 0.854,0.823 0.125,0.146 10 false 5 0.906,0.656 1.208,0.802 0.302,0.146 10 false AM2 0.563,3.844 0.865,3.99 0.302,0.146 10 false AM2 1.49,0.646 1.771,0.792 0.281,0.146 10 false ST2 1.844,0.667 1.969,0.813 0.125,0.146 10 false 7 0.854,1.292 1.167,1.458 0.313,0.167 10 false G9 0.854,1.448 1.781,1.917 0.927,0.469 10 false Ignition Switch Assembly 3.26,3.833 3.49,3.99 0.229,0.156 10 false ST 3.021,3.396 3.146,3.552 0.125,0.156 10 false 1 3.031,4.302 3.156,4.458 0.125,0.156 10 false 2 2.552,3.406 2.677,3.563 0.125,0.156 10 false 5 2.552,4.302 2.677,4.458 0.125,0.156 10 false 3 1.75,4.833 2.073,4.99 0.323,0.156 10 false C32 1.583,4.833 1.708,5 0.125,0.167 10 false 1 1.115,4.885 1.24,5.052 0.125,0.167 10 false 1 1.073,5.063 1.354,5.219 0.281,0.156 10 false D4 1.479,5.854 2.135,6.281 0.656,0.427 10 false Starter Assembly 0.74,5.896 1.219,6.156 0.479,0.26 10 false Battery 5.271,3.031 5.635,3.177 0.365,0.146 10 false C131 5.271,0.771 5.667,0.917 0.396,0.146 10 false C130

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally.

If the engine will not crank, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Check the value displayed on the tester when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Condition Display (Starter Signal)
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (STA TERMINAL VOLTAGE)

NG

3.INSPECT ECM (STA TERMINAL VOLTAGE)
a.
A255762
1.521,0.635 1.948,0.885 0.427,0.25 1.792,2.219 2.125,2.938 true 1.833,2.969 2.5,3.229 0.667,0.26 10 false 11 (STA) 0.208,0.125 0.427,0.313 0.219,0.188 10 false *a 1.573,0.677 1.969,0.885 0.396,0.208 10 false C131
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Switch Condition Specified Condition Proceed to
C131-11 (STA) - Body ground Ignition switch
ON
Below 1.5 V A
11 to 14 V B




A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ST RELAY)