Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

When the engine speed is between 2200 rpm and 4100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status) to close the IACV. Under other conditions, the VSV is usually OFF and the IACV is open.

A115903
0.531,0.865 0.927,1.177 false 2.74,1.208 2.771,1.604 false 5.573,0.396 5.417,0.646 false 0.896,0.385 1.052,0.563 0.156,0.177 10 false 6 1.26,0.385 1.417,0.563 0.156,0.177 10 false 4 1.625,0.385 1.781,0.563 0.156,0.177 10 false 2 0.896,1.854 1.052,2.031 0.156,0.177 10 false 5 1.271,1.854 1.427,2.031 0.156,0.177 10 false 3 1.615,1.854 1.771,2.031 0.156,0.177 10 false 1 0.177,0.76 0.594,0.927 0.417,0.167 10 false IACV 2.469,1.615 3.406,1.781 0.938,0.167 10 false Throttle Valve 5.604,0.26 7.156,0.427 1.552,0.167 10 false Valve Closed (VSV: ON) 4.24,0.427 5.177,0.854 0.938,0.427 10 false Throttle Valve Opening Angle 5.594,2.333 6.917,2.573 1.323,0.24 10 false Engine Speed (rpm) 5.177,2.073 5.635,2.26 0.458,0.188 10 false 2200 4.906,1.094 5.167,1.365 0.26,0.271 10 false 60° 6.042,2.083 6.469,2.281 0.427,0.198 10 false 4100

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) Conditions (a) and (b) are met for 0.5 seconds or more (2 trip detection logic):
(a) The voltage of terminal ACIS of the ECM is low when the VSV is OFF.
(b) The engine has started.
·

Open or short in VSV for ACIS circuit

·

VSV for ACIS

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A279110
4.354,1.302 4.771,1.469 0.417,0.167 10 false C139 4.354,1.458 5.25,1.635 0.896,0.177 10 false VSV for ACIS 4.344,0.865 4.458,1.031 0.115,0.167 10 false 1 5.125,0.875 5.24,1.042 0.115,0.167 10 false 2 5.948,0.875 6.354,1.042 0.406,0.167 10 false ACIS 5.948,2.021 6.396,2.188 0.448,0.167 10 false MREL 3.313,0.823 3.427,0.99 0.115,0.167 10 false 5 3.271,0.99 3.5,1.156 0.229,0.167 10 false 1J 3.313,1.313 3.427,1.479 0.115,0.167 10 false 2 3.271,1.49 3.5,1.656 0.229,0.167 10 false 1J 1.615,0.802 1.729,0.969 0.115,0.167 10 false 1 1.573,0.979 1.802,1.146 0.229,0.167 10 false 1H 1.615,1.302 1.729,1.469 0.115,0.167 10 false 3 1.594,1.479 1.823,1.646 0.229,0.167 10 false 1J 1.99,1.104 2.26,1.271 0.271,0.167 10 false EFI 2.583,1.802 3.01,1.969 0.427,0.167 10 false MAIN 1.771,2.177 3.323,2.365 1.552,0.188 10 false No. 1 Integration Relay 0.406,1.573 0.802,1.917 0.396,0.344 10 false BATT P/I 0.542,2.76 1.031,2.958 0.49,0.198 10 false Battery 5.531,0.979 5.927,1.135 0.396,0.156 10 false C129 5.615,0.813 5.813,0.979 0.198,0.167 10 false 33 5.521,2.135 5.896,2.292 0.375,0.156 10 false G155 5.646,1.948 5.781,2.115 0.135,0.167 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR INTAKE CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Intake Control
50004 61 3

d.

Check if an operating noise can be heard when operating the air intake control valve using the intelligent tester.

OK:

Operating noise can be heard.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT VSV FOR ACIS (RESISTANCE)
2.INSPECT VSV FOR ACIS (RESISTANCE)

OK

3.INSPECT VSV FOR ACIS (POWER SOURCE)

NG

REPLACE VSV FOR ACIS

3.INSPECT VSV FOR ACIS (POWER SOURCE)
a.
A219139
0.51,1.021 0.896,1.271 0.385,0.25 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 0.552,1.063 0.927,1.281 0.375,0.219 10 false C139
*a Front view of wire harness connector
(to VSV for ACIS)


Disconnect the VSV for ACIS connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C139-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM)
a.

Disconnect the VSV for ACIS connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C139-2 - C129-33 (ACIS) Always Below 1 Ω
C139-2 or C129-33 (ACIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - NO. 1 INTEGRATION RELAY)
a.

Disconnect the VSV for ACIS connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C139-1 - 1J-5 Always Below 1 Ω
C139-1 or 1J-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR AND REPLACE FUSE