Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2119  Throttle Actuator Control Throttle Body Range / Performance  


SYSTEM DESCRIPTION

The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, throttle position sensor, accelerator pedal position sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The throttle position sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2119 Throttle Actuator Control Throttle Body Range / Performance The throttle valve opening angle continues to vary greatly from the target opening angle.
(1 trip detection logic)
·

Electronic Throttle Control System (ETCS)

·

ECM

·

Wire harness or connector


Comes on DTC stored

MONITOR DESCRIPTION

The ECM determines the actual opening angle of the throttle valve from the throttle position sensor signal. The actual opening angle is compared to the target opening angle commanded by the ECM. If the difference between these two values is outside the standard range, the ECM interprets this as a malfunction in the ETCS. The ECM then illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored when the accelerator pedal is quickly released (to close the throttle valve) after the engine speed reaches 5000 rpm by fully depressing the accelerator pedal (fully open the throttle valve).

CONFIRMATION DRIVING PATTERN

A199316
1.458,2.24 1.656,2.448 0.198,0.208 10 false [A] 2.667,3.292 2.885,3.49 0.219,0.198 10 false [B] 6.156,3.302 6.5,3.646 0.344,0.344 10 false [C] 0.448,0.74 1.135,0.938 0.688,0.198 10 false Released 0.365,0.438 1.073,0.646 0.708,0.208 10 false Depressed 0.688,1.844 1.083,2.031 0.396,0.188 10 false Idling 0.177,2.115 1.188,2.573 1.01,0.458 10 false Ignition Switch ON 0.073,0.146 1.74,0.354 1.667,0.208 10 false Accelerator Pedal State 1.844,2.656 2.625,2.854 0.781,0.198 10 false 20 seconds

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine.

7.

Idle the engine for 20 seconds.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2119.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, fully depress and release the accelerator pedal 3 times, and then check the DTC judgment result [C].




FAIL-SAFE

When this DTC, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P2119 is output A
P2119 and other DTCs are output B


HINT:

If any DTCs other than P2119 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

B

2.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position Command.

Powertrain > Engine > Data List
Tester Display
Throttle Position No.1
Throttle Position Command
50003 61 112,125

h.

Check the values displayed on the tester while fully depressing and releasing the accelerator pedal quickly.

Result:
Result Proceed to
Throttle Position No. 1 does not change A
Throttle Position No. 1 changes even a little B


HINT:

When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.




A

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)

B

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

7.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body with motor assembly. Also, check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

NG

7.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
5.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

Powertrain > Engine > Data List
Tester Display
Throttle Position No.1
Throttle Position No.2
Throttle Position Command
50003 61 112,113,125

h.

Check the values displayed on the tester while wiggling the ECM wire harness.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Check for DTCs.

Result:
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B




A

6.REPAIR OR REPLACE HARNESS OR CONNECTOR

B

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P2119 is output B




A

END

B