Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM.

By turning the ignition switch to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A253412
6.01,0.833 6.24,0.99 0.229,0.156 10 false W 5.74,0.833 5.938,0.99 0.198,0.156 10 false 30 6.24,2.719 6.667,2.885 0.427,0.167 10 false G154 6.25,2.865 6.615,3.031 0.365,0.167 10 false ECM 3.604,0.844 3.802,1.01 0.198,0.167 10 false 21 5.292,0.833 5.5,1 0.208,0.167 10 false 39 3.979,1.427 4.323,1.583 0.344,0.156 10 false G19 3.979,1.573 5.167,2.042 1.188,0.469 10 false Combination Meter Assembly 2.917,1.104 3.26,1.26 0.344,0.156 10 false MET 0.552,1.927 0.906,2.094 0.354,0.167 10 false AM2 1.521,0.833 1.865,1 0.344,0.167 10 false AM2 2.115,0.833 2.438,1 0.323,0.167 10 false IG2 1.365,0.833 1.479,0.99 0.115,0.156 10 false 5 2.417,0.833 2.531,0.99 0.115,0.156 10 false 6 1.49,1.51 2.396,1.948 0.906,0.438 10 false Ignition Switch Assembly 1.49,1.354 1.771,1.51 0.281,0.156 10 false G9 0.677,2.76 1.167,2.938 0.49,0.177 10 false Battery 3.844,0.76 4.208,0.927 0.365,0.167 10 false IG+ 4.948,0.75 5.302,0.896 0.354,0.146 10 false CHK

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the chart below.

Result:
Result Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check whether any DTCs have been stored. Note them down if necessary.

Powertrain > Engine > Trouble Codes
50001 61

e.

Clear DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

f.

Check if the MIL turns off.

OK:

MIL turns off.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A253416
2.073,0.542 2.5,0.792 0.427,0.25 0.26,0.042 0.479,0.229 0.219,0.188 10 false *a 2.135,0.583 2.49,0.75 0.354,0.167 10 false G154
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G154-30 (W) - G19-39 (CHK) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turns ON.

OK:

MIL is illuminated.



Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G154-30 (W) - G19-39 (CHK) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR