Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646
1.656,0.844 2.969,1.135 1.313,0.292 10 false from EFI Fuse 1.531,1.177 2.635,1.375 1.104,0.198 10 false from MAIN Fuse 0.26,1.802 2.708,2.417 2.448,0.615 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have an IC) 0.229,2.708 2.656,3.271 2.427,0.563 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.927,3.083 5.333,3.448 0.406,0.365 10 false ECM 2.875,0.74 3.26,0.885 0.385,0.146 10 false BATT 2.823,1.083 3.448,1.292 0.625,0.208 10 false +B, +B2 3.01,1.99 3.292,2.177 0.281,0.188 10 false VC 4.396,0.896 6.188,1.25 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.792 6.354,2.146 0.99,0.354 10 false Microprocessor 4.073,2.844 4.219,3.01 0.146,0.167 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A279114
2.667,0.833 3.083,0.979 0.417,0.146 10 false VCPA 3.229,0.729 3.375,0.917 0.146,0.188 10 false 4 4.906,0.667 5.104,0.813 0.198,0.146 10 false 26 4.802,0.823 5.198,0.969 0.396,0.146 10 false G155 4.906,0.99 5.104,1.135 0.198,0.146 10 false 18 4.802,1.146 5.198,1.292 0.396,0.146 10 false G155 4.906,1.313 5.104,1.458 0.198,0.146 10 false 20 4.802,1.469 5.198,1.615 0.396,0.146 10 false G155 4.906,1.635 5.104,1.781 0.198,0.146 10 false 27 4.802,1.792 5.198,1.938 0.396,0.146 10 false G155 4.906,1.948 5.104,2.094 0.198,0.146 10 false 19 4.802,2.104 5.198,2.25 0.396,0.146 10 false G155 4.906,2.271 5.104,2.417 0.198,0.146 10 false 21 4.802,2.427 5.198,2.573 0.396,0.146 10 false G155 2.76,1.135 3.083,1.281 0.323,0.146 10 false VPA 3.229,1.042 3.375,1.229 0.146,0.188 10 false 6 2.76,1.469 3.083,1.615 0.323,0.146 10 false EPA 3.229,1.375 3.375,1.563 0.146,0.188 10 false 5 2.688,1.781 3.104,1.927 0.417,0.146 10 false VCP2 3.229,1.688 3.375,1.875 0.146,0.188 10 false 1 2.688,2.104 3.104,2.25 0.417,0.146 10 false VPA2 3.229,2 3.375,2.188 0.146,0.188 10 false 3 2.844,3.448 3.083,3.594 0.24,0.146 10 false VC 3.229,3.354 3.375,3.542 0.146,0.188 10 false 5 2.771,3.781 3.094,3.927 0.323,0.146 10 false VTA 3.229,3.677 3.375,3.865 0.146,0.188 10 false 6 2.708,4.125 3.104,4.271 0.396,0.146 10 false VTA2 3.229,4.031 3.375,4.219 0.146,0.188 10 false 4 2.719,7.646 3.094,7.792 0.375,0.146 10 false VVL+ 3.229,7.552 3.375,7.74 0.146,0.188 10 false 1 2.74,7.979 3.094,8.125 0.354,0.146 10 false VVL- 3.229,7.875 3.375,8.063 0.146,0.188 10 false 2 2.865,7.302 3.156,7.448 0.292,0.146 10 false VC 3.229,7.198 3.375,7.385 0.146,0.188 10 false 3 2.865,4.469 3.083,4.615 0.219,0.146 10 false E2 3.229,4.365 3.375,4.552 0.146,0.188 10 false 3 2.688,2.417 3.104,2.563 0.417,0.146 10 false EPA2 5.229,0.74 5.646,0.885 0.417,0.146 10 false VCPA 5.75,8.406 6.125,8.552 0.375,0.146 10 false ECM 5.229,1.135 5.552,1.281 0.323,0.146 10 false VPA 5.229,1.385 5.552,1.531 0.323,0.146 10 false EPA 5.229,1.698 5.646,1.844 0.417,0.146 10 false VCP2 4.906,3.292 5.104,3.438 0.198,0.146 10 false 23 4.802,3.448 5.198,3.594 0.396,0.146 10 false C129 4.906,3.625 5.104,3.771 0.198,0.146 10 false 20 4.802,3.792 5.198,3.938 0.396,0.146 10 false C129 4.906,3.958 5.104,4.104 0.198,0.146 10 false 19 4.802,4.125 5.198,4.271 0.396,0.146 10 false C129 4.906,4.302 5.104,4.448 0.198,0.146 10 false 28 4.802,4.469 5.198,4.615 0.396,0.146 10 false C129 5.229,3.375 5.51,3.521 0.281,0.146 10 false VC 5.229,3.771 5.698,3.917 0.469,0.146 10 false VTA1 5.229,4.104 5.635,4.25 0.406,0.146 10 false VTA2 5.229,4.365 5.646,4.51 0.417,0.146 10 false E2 4.896,7.458 5.094,7.604 0.198,0.146 10 false 18 4.802,7.646 5.198,7.792 0.396,0.146 10 false C131 5.229,7.656 5.646,7.802 0.417,0.146 10 false VV2+ 4.906,7.813 5.115,7.958 0.208,0.146 10 false 28 4.802,7.99 5.198,8.135 0.396,0.146 10 false C131 5.229,7.99 5.646,8.135 0.417,0.146 10 false VV2- 4.906,6.094 5.104,6.24 0.198,0.146 10 false 29 4.906,5.75 5.104,5.896 0.198,0.146 10 false 19 4.802,6.26 5.198,6.406 0.396,0.146 10 false C131 5.229,6.26 5.719,6.406 0.49,0.146 10 false VV1- 4.802,5.917 5.198,6.063 0.396,0.146 10 false C131 5.229,5.917 5.646,6.063 0.417,0.146 10 false VV1+ 5.229,2.094 5.646,2.24 0.417,0.146 10 false VPA2 5.229,2.333 5.646,2.479 0.417,0.146 10 false EPA2 3.229,2.323 3.375,2.51 0.146,0.188 10 false 2 0.583,0.688 0.865,0.854 0.281,0.167 10 false G6 0.583,0.875 2.49,1.406 1.906,0.531 10 false Accelerator Pedal Position Sensor (Built into Accelerator Pedal Rod Assembly) 0.583,3.292 0.865,3.458 0.281,0.167 10 false C67 0.594,3.448 2.052,4.063 1.458,0.615 10 false Throttle Position Sensor (Built into Throttle Body with Motor Assembly) 0.604,7.188 1.021,7.354 0.417,0.167 10 false C146 0.604,7.333 2.323,7.5 1.719,0.167 10 false VVT Sensor (for Bank 2) 2.844,5.583 3.073,5.729 0.229,0.146 10 false VC 3.229,5.479 3.375,5.667 0.146,0.188 10 false 3 2.688,5.917 3.115,6.063 0.427,0.146 10 false VVR+ 3.229,5.813 3.375,6 0.146,0.188 10 false 1 2.729,6.26 3.115,6.406 0.385,0.146 10 false VVR- 3.229,6.156 3.375,6.344 0.146,0.188 10 false 2 0.583,5.417 1.063,5.583 0.479,0.167 10 false C138 0.583,5.563 2.156,5.729 1.573,0.167 10 false VVT Sensor (for Bank 1)

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check the communication between the tester and ECM.

Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)

B

3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

4.CHECK MIL (ACCELERATOR PEDAL ROD ASSEMBLY)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL ROD ASSEMBLY)
a.

Disconnect the accelerator pedal rod assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

5.CHECK MIL (VVT SENSOR FOR BANK 1)

B

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

5.CHECK MIL (VVT SENSOR FOR BANK 1)
a.

Disconnect the VVT sensor (for bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

6.CHECK MIL (VVT SENSOR FOR BANK 2)

B

6.CHECK MIL (VVT SENSOR FOR BANK 2)
a.

Disconnect the VVT sensor (for bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

7.CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT)

B

7.CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal rod assembly connector.


c.

Disconnect the VVT sensor (for bank 1) connector.


d.

Disconnect the VVT sensor (for bank 2) connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C129-23 (VC) - Body ground Always 10 kΩ or higher
G155-26 (VCPA) - Body ground Always 10 kΩ or higher
G155-27 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR