Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A132329
1.344,1.729 1.573,1.5 false 1.573,1.5 1.771,1.5 false 0.125,0.156 0.896,0.5 0.771,0.344 10 false Fig. 1: 0.125,0.417 1.135,0.698 1.01,0.281 10 false Resistance 0.219,0.896 0.615,1.177 0.396,0.281 10 false (kΩ) 1.823,1.417 2.719,1.813 0.896,0.396 10 false Acceptable 1.427,4.115 2.313,4.396 0.885,0.281 10 false Temperature 3.063,3.656 3.344,3.896 0.281,0.24 10 false (°C) 3.063,3.833 3.344,4.083 0.281,0.25 10 false (°F)

The intake air temperature sensor, which is built into the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the intake air temperature. When the intake air temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. The intake air temperature sensor is powered by a 5 V supply from terminal THA of the ECM via resistor R. Since resistor R and the intake air temperature sensor are connected in series, when the resistance of the intake air temperature sensor changes depending on the intake air temperature, the voltage at terminal THA also varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Circuit Low Input A short in the intake air temperature sensor circuit for 0.5 seconds (1-trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input An open in the intake air temperature sensor circuit for 0.5 seconds (1-trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the intake air temperature using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


WIRING DIAGRAM

A162760
0.417,1.813 0.979,2.021 0.563,0.208 10 false C36 2.021,0.615 2.396,0.823 0.375,0.208 10 false THA 2.125,1.229 2.406,1.458 0.281,0.229 10 false E2 2.448,0.615 2.688,0.823 0.24,0.208 10 false 4 2.448,1.229 2.688,1.438 0.24,0.208 10 false 5 5.25,0.615 5.49,0.823 0.24,0.208 10 false 12 6.198,0.177 6.51,0.385 0.313,0.208 10 false 5 V 6.281,0.583 6.521,0.792 0.24,0.208 10 false R 5.521,0.615 5.906,0.823 0.385,0.208 10 false THA 5.521,1.229 5.948,1.438 0.427,0.208 10 false ETHA 5.969,2.26 6.396,2.469 0.427,0.208 10 false C95 5.969,2.427 6.396,2.635 0.427,0.208 10 false ECM 5.25,1.24 5.49,1.448 0.24,0.208 10 false 11 0.417,1.979 2.365,2.469 1.948,0.49 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

e.

Read the value displayed on the tester.

Result:
Result Proceed to
Temperature displayed is -40°C (-40°F) A
Temperature displayed is 140°C (284°F) or higher B
Temperature displayed is same as actual intake air temperature C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A242724
0.208,2.406 0.542,2.635 0.333,0.229 1.479,3.063 1.969,2.615 true 2.448,3.042 2.229,2.625 true 0.646,0.125 0.958,0.281 0.313,0.156 10 false *1 2.563,0.115 2.875,0.271 0.313,0.156 10 false *2 0.698,1.531 1.01,1.813 0.313,0.281 10 false *a 2.469,0.865 2.865,1.073 0.396,0.208 10 false THA 2.458,1.313 2.948,1.521 0.49,0.208 10 false ETHA 2.49,2.969 2.979,3.177 0.49,0.208 10 false E2 1.354,3.083 1.833,3.292 0.479,0.208 10 false THA 0.25,2.438 0.729,2.646 0.479,0.208 10 false C36
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Confirm that there is a good connection at the mass air flow meter.


b.

Disconnect the mass air flow meter connector.


c.

Connect terminals THA and ETHA of the wire harness connector for the mass air flow meter.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the tester on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

h.

Read the value displayed on the tester.

Standard value:

140°C (284°F)



i.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-4 (THA) - C95-12 (THA) Always Below 1 Ω
C36-5 (E2) - C95-11 (ETHA) Always Below 1 Ω



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A211723
0.708,0.25 1.083,0.521 0.375,0.271 10 false *1 2.615,0.24 2.938,0.458 0.323,0.219 10 false *2 2.427,1 2.802,1.271 0.375,0.271 10 false THA 2.438,1.458 2.917,1.729 0.479,0.271 10 false ETHA
*1 Mass Air Flow Meter
*2 ECM


Disconnect the mass air flow meter connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

f.

Read the value displayed on the tester.

Standard value:

-40°C (-40°F)



g.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-4 (THA) or C95-12 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)